Niles Audio ZR-6 manual Ir Programming, Programming Source Device Ir Command Codes, Overview

IR PROGRAMMING

PROGRAMMING SOURCE DEVICE IR COMMAND CODES

Press the – button to exit and move to the next step without erasing any of the presets.

To continue to the next confi guration step, RESTORING FACTORY DEFAULTS, press the Set button.

To save the settings and exit confi guration mode, simultaneously hold down the Band and Set buttons. After the ZR-6 saves the information, [RELEASE BUTTONS TO CONTINUE] appears on the display. The ZR-6 will return to the normal operating mode.

RESTORING THE FACTORY DEFAULTS

While in confi guration mode, press the Set button until [FACTORY RESET] appears on the display.

F A C T O R Y R E S E T

- / N O + / Y E S

Press + to erase all confi guration data. All Master/Slave, zone linking, paging, party mode, bass, treble, and loudness settings will return to the factory default. NOTE: Learned IR commands will not be erased. The display will show [CONFIRM ERASE].

C O N F I R M E R A S E

- / N O + / Y E S

Press the + button to confi rm the erase procedure. The display will show [MASTER DEFAULT RESTORED].

M A S T E R

D E F A U L T R E S T O R E D

Press the – button (at either screen) to exit and move to the next step without erasing any information.

To continue to the fi rst confi guration step, MASTER/SLAVE, press the Set button.

To save the settings and exit confi guration mode, simultaneously hold down the Band and Set buttons. After the ZR-6 saves the information, [RELEASE BUTTONS TO CONTINUE] appears on the display. The ZR-6 will return to the normal operating mode .

OVERVIEW

By default, the connected keypads and the R-8L hand-held remote will control source selection, AM/FM tuner functions, iPod functions, zone volume level, and on/off for the zone and system. To enable full control of any other connected source devices, the IR command codes for these source devices must be learned and stored in the ZR-6 MultiZone Receiver. The keypads and R-8L hand-held remote will then control the source devices by sending the IR command codes stored in the ZR-6 MultiZone Receiver through MicroFlashers attached to the source devices.

HOW IR COMMAND CODES ARE ENTERED AND STORED

The source device IR command codes are entered in the ZR-6 MultiZone Receiver using the source device factory remote controls. The ZR-6 supplies each source device with a memory page to store its IR command codes. The individual command codes (Play, Pause, etc.) are stored in memory cells within each page, pre-labeled to match the commands available on the R-8L remote control.

LIBRARY 1 AND VS-6/LIBRARY 2

In addition to the fi ve source device IR storage pages, the ZR-6 MultiZone Receiver provides two additional areas to store IR command codes: Library 1 or the VS-6/Library 2. The Libraries are typically used to store the IR command codes from non-source devices such as draperies, television lifts, or other codes that the installer prefers to be easily accessible. By default, Library 1 is empty and Library 2 is fi lled with the IR command codes for the Niles VS-6 Component High Defi nition Video Switcher (see VS-6 IR Command Set section). If a VS-6 is not being used, new IR command codes can be learned in place of these.

IR COMMAND CODE PROGRAMMING PROCEDURE

The source device IR command code programming is organized into source device memory pages, and then command code memory cells within the memory pages.

The source device memory pages appear in this order:

Page 1	Source 2 (Only if a source name other than
	“iPod or “N/A’ was specifi ed in “Naming
	Source Devices”
Page 2	Source 3
Page 3	Source 4

(CONTINUED ON NEXT PAGE)

40 NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 305-238-4373