Extron electronic manual Specificationsecifications, cont’d, SGS 408 Switcher Specifications

Page 54

Specificationsecifications, cont’d

Video

Routing	8 x 2 matrix
Gain	Variable, set by the contrast control

Video input

Number/signal type	8 RGBHV, RGBS, RGsB, component video
Connectors	8 x 5 BNC female
Nominal level	1 Vp-p for Y of component video
	0.7 Vp-p for RGB and for R-Y and B-Y of component video
Minimum/maximum levels	0 V to 2.0 Vp-p with no offset
Impedance	75 ohms
Input termination	High Z
Horizontal frequency	Autoscan 15 kHz to 100 kHz
Vertical frequency	Autoscan 50 Hz to 120 Hz
Resolution range	Autoscan 560 x 384 to 1600 x 1200
DC offset (max. allowable)	0.5 V

Video processing

Digital sampling	24 bit, 8 bits per color; 140 MHz standard
Horizontal filtering	8 levels
Vertical filtering	8 levels
Frame rate delay	0 to 1 field

Video output

Number/signal type	2 (program and preview) RGBHV, RGBS
Connectors	Program output: 5 BNC female, (1) 15-pin HD female
	Preview output: 5 BNC female, (1) 15-pin HD female, 1 DVI (optional)
Nominal level	0.7 Vp-p for RGB
Minimum/maximum levels	0 V to 0.7 Vp-p
Impedance	75 ohms
Scaled resolutions	640x4801,3,4,5, 800x6001,3,4,5, 832x6243,4,5, 848x4803,5, 852x4803,5, 1024x7681,3,4,5,
	1280x7682,5, 1280x10241,3,5, 1360x7653,5, 1365x10243,5, 1400x10501,3,5, 576p1,5,
	720p3,5, 1080i1,3,5, and 1080p3,5
	1 = at 50 Hz 2 = at 56 Hz 3 = at 60 Hz 4 = at 75 Hz
	5 = locked to the current vertical refresh rate of input 1 (Accu-RATE Frame
	Lock)
DC offset	±50 mV (max.) with input at 0 offset

Sync

Input type	Autodetect RGBHV, RGBS, RGsB
Output type	RGBHV, RGBS
Input level	3.0 V to 5.0 Vp-p
Output level	TTL: 5.0 Vp-p, unterminated
Input impedance	510 ohms
Output impedance	75 ohms
Max input voltage	5.0 Vp-p
Polarity	Composite sync: negative
	H/V: user-selectable

Control/remote — switcher

Serial control port

RS-232, 9-pin female D connector

A-2 SGS 408 Switcher • Specifications

Image 54

Contents Eight Input, High Resolution, Seamless Graphic Switcher SGSSicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolQuick Start SGS SGS 408 Quick Start QS-1Button Right adjustment knob Left adjustment knob Button Right adjustment knobLeft adjustment knob Quick Start SGS 408, cont’dTable of Contents Table of Contents, cont’d One Introductiontroduction, cont’d FeaturesSGS 408 Switcher Introduction About the SGSSGS 408 Switcher Introduction Introduction, cont’d Two Installation Installationstallation, cont’dRear Panel Connectors SGS 408 Switcher InstallationMounting the switcher Rack mountingInstallation, cont’d CablingTabletop/desktop mounting Genlocking Video Inputs for Accu-RATE Frame Lock SGSAttaching an RCP Attaching an ECPPin Signal Cable PinoutsXLR cable pinouts DVI cable pinouts Making an RCP comm cableThree SGS 408 Switcher Operation Operationeration, cont’dFront Panel Controls Default Screen LCD default screenConfiguring the SGS Operation, cont’dSelecting the input configuration Selecting the input configuration menuSelecting the output rate Selecting the output sync format and polaritySelecting a test pattern Rgbs RgbhvChanging the title settings 12 Test patterns15 ECP control Setting the program keylock 18 Resetting the title box submenu controlsSetting the LCD appearance Performing a reset23 Performing a reset Using the Image Controls Centering an imageSizing an image Adjusting contrast and brightness Filtering an imageSelecting an Input Freezing an inputApplying other effects Using the Black buttonApplying a cut Available effects32 Standard wipe transitions 35 Square wipe effects Setting up a new effect 37 ECP key title effect38 Setting up the Dissolve effect 41 Setting up the S curtains effect 44 Setting up the Square wipe effect Implementing an established effectUsing executive mode Implementing a titleOptimizing the Image Four RS-232 Programmer’s Guide SGS 408 Switcher Serial CommunicationSerialCommunicationunication, c t’d SGS-initiated messagesSGS error responses Using the command/response tableCommand/response table Serial Communication, cont’dCommand Ascii Response Description Command Ascii Installing the software Control Software for WindowsAdvanced Instructions Using the software SGS 408 Control Program windowFive SGS 408 Switcher Troubleshooting Troubleshootingubleshooting, cont’dIf the switcher does not respond to controls If the image does not appearAAppendix a Specificationsecifications, cont’d SGS 408 Switcher SpecificationsGeneral Specifications, cont’d AppendixBB Installing the DVI connector option Upgrades and RepairsInternal access SGS 408 Switcher Reference InformationFigure B-2 Installing the DVI connector option Replacing the AC fuseInstalling a firmware update Reference Information, cont’dFigure B-4 Locating and replacing ICs Part Numbers Related part numbersExtron Part Part Number FCC Class a Notice Extron’s Warranty Extron Electronics, USA