Extron electronic SGS 408 manual Selecting the output rate

Page 24

Operation, cont’d

6.Depending on the input type, color matrix, Beta-cam control, and Luma/ Setup control can be set by pressing the button below each control (figure 3-7). Color matrix control may be set to either the ITU 601 or ITU 709 standard, Beta-cam control may be set on or off, and Luma/Setup control may be set to either .700V or .714V, on or off.

There are four preset component video types available for selection. The settings for each control can be changed by pressing the button below it. If needed, a custom component setting may be made.

7.To return to the default LCD menu, press the Exit button, then press the Next button, then press the Exit button, or wait 16 seconds until the submenu times out.

Selecting the output rate

To select the output rate, do the following:

1.Press the Menu button.

2.Press the Out Rate button (figure 3-9).

Tr u e ( D V I ) o n l y

 

 

 

 

 

1 2 8 0 x 1 0 2 4

 

 

 

 

 

 

 

 

 

 

 

 

6 0 H z

 

 

 

I n p u t

O u t

O u t

T e s t

N e x t

C o n f i g

R a t e

S y n c

P a t t e r n

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 3-9 — Selecting the output rate

3.To select the output resolution, turn the right adjustment knob. The following output rates are available:

640

x 4801,2,3,4

852 x 4802,4

1360

x 7652,4

720p2,4

800

x 6001,2,3,4

1024

x 7681,2,3,4

1365

x 10242,4

1080i1,2,4

832

x 6242,3,4

1280

x 7684,5

1400

x 10501,2,4

1080p2,4

848

x 4802,4

1280

x 10241,2,4

576p1,4

 

1 at 50 Hz; 2 at 60 Hz;

3 at 75 Hz;

4 locked to the current vertical refresh

rate of input 1;

5 at 56 Hz

 

 

 

4.To select the refresh rate, turn the left adjustment knob. The available refresh rates depend on the output resolution. The locking feature will lock the output rate to the vertical refresh rate of input 1.

5.Pressing the Output Rate button allows the scaler to be set to True DVI or Enhanced mode. True DVI is only available for resolutions of 1024 x 768 and above. When using the optional DVI output card, control must be set to True DVI.

6.To return to the default LCD menu, press the Next button, then press the Exit button, or wait 16 seconds until the submenu times out.

Selecting the output sync format and polarity

To select the output sync format, do the following:

1.Press the Menu button.

2.Press the Out Sync button (figure 3-10).

3-6 SGS 408 Switcher • Operation

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Eight Input, High Resolution, Seamless Graphic Switcher SGSSafety Instructions English Consignes de Sécurité FrançaisSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolQuick Start SGS SGS 408 Quick Start QS-1Button Right adjustment knob Left adjustment knobButton Right adjustment knob Left adjustment knob Quick Start SGS 408, cont’dTable of Contents Table of Contents, cont’d One Features SGS 408 Switcher IntroductionIntroductiontroduction, cont’d About the SGSSGS 408 Switcher Introduction Introduction, cont’d Two Installationstallation, cont’d Rear Panel ConnectorsInstallation SGS 408 Switcher InstallationMounting the switcher Rack mountingInstallation, cont’d CablingTabletop/desktop mounting Genlocking Video Inputs for Accu-RATE Frame Lock SGSAttaching an RCP Attaching an ECPPin Signal Cable PinoutsXLR cable pinouts DVI cable pinouts Making an RCP comm cableThree SGS 408 Switcher Operation Operationeration, cont’dFront Panel Controls Default Screen LCD default screenConfiguring the SGS Operation, cont’dSelecting the input configuration Selecting the input configuration menuSelecting the output rate Selecting the output sync format and polaritySelecting a test pattern Rgbs RgbhvChanging the title settings 12 Test patterns15 ECP control Setting the program keylock 18 Resetting the title box submenu controlsSetting the LCD appearance Performing a reset23 Performing a reset Using the Image Controls Centering an imageSizing an image Adjusting contrast and brightness Filtering an imageSelecting an Input Freezing an inputUsing the Black button Applying a cutApplying other effects Available effects32 Standard wipe transitions 35 Square wipe effects Setting up a new effect 37 ECP key title effect38 Setting up the Dissolve effect 41 Setting up the S curtains effect 44 Setting up the Square wipe effect Implementing an established effectUsing executive mode Implementing a titleOptimizing the Image Four SGS 408 Switcher Serial Communication SerialCommunicationunication, c t’dRS-232 Programmer’s Guide SGS-initiated messagesSGS error responses Using the command/response tableCommand/response table Serial Communication, cont’dCommand Ascii Response Description Command Ascii Installing the software Control Software for WindowsAdvanced Instructions Using the software SGS 408 Control Program windowFive Troubleshootingubleshooting, cont’d If the switcher does not respond to controlsSGS 408 Switcher Troubleshooting If the image does not appearAAppendix a Specificationsecifications, cont’d SGS 408 Switcher SpecificationsGeneral Specifications, cont’d AppendixBB Upgrades and Repairs Internal accessInstalling the DVI connector option SGS 408 Switcher Reference InformationFigure B-2 Installing the DVI connector option Replacing the AC fuseInstalling a firmware update Reference Information, cont’dFigure B-4 Locating and replacing ICs Part Numbers Related part numbersExtron Part Part Number FCC Class a Notice Extron’s Warranty Extron Electronics, USA
Top Page Image Contents