Extron electronic manual Front Panel Controls and Indicators, SVS 100 Operation

Page 20
INPUT 4
RESET

Operation

Front Panel Controls and Indicators

The front panel (see figure 3-1and figure 3-2) features all of the direct access controls and indicators, including video input selection, switching effects, picture controls, genlock controls, top and bottom blanking, audio level, an encoder knob for making adjustments, and an LCD display. The front panel controls (but not the Input buttons) may also be disabled through the Executive mode command (see the Executive Mode section in this chapter).

INPUT

EXTRON

 

 

 

SVS 100

2

3

4

1

1

2

Figure 3-1 — LCD and input selection controls

1LCD — This LCD indicates status and configuration messages, menus, and the in-progress values and results of picture and audio adjustments.

Input selection controls and indicators

2Input 1, Input 2, Input 3, and Input 4 input selection buttons and LEDs — Pressing these buttons selects the associated S-video (input 1 or input 2) or composite video (inputs 1 through 4) input. Unless audio breakaway is enabled, via RS-232/RS-422 only, the audio input is switched with the video. LEDs above each button indicate the selected input. If audio is broken away, the LED associated with the selected audio input flashes, while the LED associated with the selected video input lights constantly.

Audio breakaway can be commanded through RS-232/RS-422 only, either via the Windows-based control program or using the SIS. See chapter 5, Serial Communication, for more information.

EFFECTS

 

GENLOCK

 

PICTURE CONTROLS

 

 

 

EFFECT TRANSITION DURATION

BURST

HORZ

SUB

COLOR TINT BRIGHT CONT

TOP

BOTTOM

AUDIO

 

LOCK

PHASE

PHASE

 

BLANK

BLANK

SVS

SEAMLESS VIDEO SWIT

3

4

5

6

7

8

9

10

11

12

13

14

15

Figure 3-2 — Effect, Genlock, and Picture Controls

Any individual input may be reset by holding down its input button for two seconds. During a reset, picture controls and

the audio level for that input will be reset to the factory default settings. The LCD will display an input reset menu.

3-2 SVS 100 Operation

Image 20
Contents Seamless Video Switcher SVSPrecautions Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschRack or Table/Wall Mounting Connecting the SVSQuick Start SVS Input EffectsGenlock Picture ControlsTable of Contents Table of Contents, cont’d One IntroductionSVS 100 Introduction IntroductionAbout the SVS SVS 100 Features Four Ntsc or PAL video inputsIntroduction, cont’d Installation TwoInstallation SVS 100 InstallationMounting the SVS Table or wall mountingPower connection Cabling and Rear Panel ViewsRack mounting Video input and output connectionsInstallation, cont’d Audio input and output connectionsRS-232/RS-422 connection Genlock and Vertical Interval SwitchingGenlock connections Genlock setup Oscilloscope displays Superimposed waveformsVectorscope screen during horizontal phase adjustment Three OperationFront Panel Controls and Indicators Input selection controls and indicatorsOperation SVS 100 OperationEffects controls and indicators Examples of switching effectsOperation, cont’d Genlock controls and indicators Picture controls and indicatorsAudio button Encoder knobExecutive Mode System ResetDemo mode Advanced MenusInput video type Audio switching methodVCR mode Chroma setting Optimizing the Video and Audio InputsOperation, cont’d Four Windows-based Control ProgramInstalling the Windows-based Control Software Using the SoftwareWindows-based Control Program SVS 100 Windows-based Control ProgramHelp Windows-based Control Program, cont’d Five Serial CommunicationRemote Control Port RS-232/RS-422 Serial CommunicationHost-to-SVS 100 Communication SVS 100 Serial CommunicationUsing the command/response table Serial Communication, cont’d Audio Switch Mode Example responses to commands SVS 100 CommunicationAAppendix Reference InformationSaving and Recalling Input Configuration Presets Reference InformationSpecial Applications SVS 100 AppendixConfiguring the SVS 100 for RS-422 Removing the top coverRelocating the ribbon cable and setting the jumper Replacing the top coverSVS 100 Appendix Specifications SVS Video input and loopoutGeneral SVS 100 Appendix FCC Class a Notice Extron’s Warranty Extron Electronics. All rights reserved
Related manuals
Manual 2 pages 10.59 Kb