Extron electronic SVS 100 manual Input video type, Audio switching method, VCR mode

Page 26

Operation, cont’d

Input video type

After selecting Demo mode (as previously described), the desired video input type for Input 1 may be selected by pressing the Audio button and rotating the encoder knob to select either auto, video, or S-video. Auto will automatically select the active input or, if both video and S- video are active, S-video is selected. Press the Audio button again to select the input type for Input 2. If no button is pressed within 8 seconds, the SVS 100 exits the Advanced menus.

INPUT #1

AUTO

INPUT #1

VIDEO

INPUT #1

S-VIDEO

INPUT #2

AUTO

INPUT #2

VIDEO

INPUT #2

S-VIDEO

Audio switching method

After selecting an input video type (as previously described), the desired audio switching method may be selected by pressing the Audio button and rotating the encoder knob to select either start, middle, end, or fade.

Selecting start will switch to the next audio input at the beginning of the next video input. Selecting middle will switch to the next audio halfway into the next video input. Selecting end will switch to the next audio at the end of the next video input. Selecting fade will gradually mute the current audio halfway between the switch to the new video input, then gradually increase the new audio input from mute.

AUDIO SW

START

AUDIO SW MIDDLE

AUDIO SW

END

AUDIO SW

FADE

VCR mode

After selecting an audio switching method (as previously described), the VCR mode for an input may be selected by pressing the Audio button. Selecting the VCR mode for an input will eliminate horizontal noise from the input source. Press the input button(s) to toggle the VCR mode On (Y) or Off (N).

VCR MODE Y Y Y N

3-8 SVS 100 Operation

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Seamless Video Switcher SVSConsignes de Sécurité Français PrecautionsSafety Instructions English Sicherheitsanleitungen DeutschRack or Table/Wall Mounting Connecting the SVSQuick Start SVS Genlock InputEffects Picture ControlsTable of Contents Table of Contents, cont’d One IntroductionSVS 100 Introduction IntroductionAbout the SVS SVS 100 Features Four Ntsc or PAL video inputsIntroduction, cont’d Installation TwoMounting the SVS InstallationSVS 100 Installation Table or wall mountingRack mounting Power connectionCabling and Rear Panel Views Video input and output connectionsInstallation, cont’d Audio input and output connectionsRS-232/RS-422 connection Genlock and Vertical Interval SwitchingGenlock connections Genlock setup Oscilloscope displays Superimposed waveformsVectorscope screen during horizontal phase adjustment Three OperationOperation Front Panel Controls and IndicatorsInput selection controls and indicators SVS 100 OperationEffects controls and indicators Examples of switching effectsOperation, cont’d Genlock controls and indicators Picture controls and indicatorsAudio button Encoder knobDemo mode Executive ModeSystem Reset Advanced MenusInput video type Audio switching methodVCR mode Chroma setting Optimizing the Video and Audio InputsOperation, cont’d Four Windows-based Control ProgramWindows-based Control Program Installing the Windows-based Control SoftwareUsing the Software SVS 100 Windows-based Control ProgramHelp Windows-based Control Program, cont’d Five Serial CommunicationHost-to-SVS 100 Communication Remote Control Port RS-232/RS-422Serial Communication SVS 100 Serial CommunicationUsing the command/response table Serial Communication, cont’d Audio Switch Mode Example responses to commands SVS 100 CommunicationAAppendix Reference InformationSpecial Applications Saving and Recalling Input Configuration PresetsReference Information SVS 100 AppendixConfiguring the SVS 100 for RS-422 Removing the top coverRelocating the ribbon cable and setting the jumper Replacing the top coverSVS 100 Appendix Specifications SVS Video input and loopoutGeneral SVS 100 Appendix FCC Class a Notice Extron’s Warranty Extron Electronics. All rights reserved
Related manuals
Manual 2 pages 10.59 Kb
Top Page Image Contents