Extron electronic SVS 100 manual Cabling and Rear Panel Views, Rack mounting, Power connection

Page 13

Rack mounting

Rack mount the switcher as follows:

1. Attach the rack mount brackets to the switcher with eight #8 machine screws, provided (see figure 2-1).

2. Insert the switcher into the rack, align the holes in the mounting bracket with those of the rack.

3. Secure the switcher to the rack using the supplied machine screws.

Cabling and Rear Panel Views

All connectors are on the rear panel (see figures 2-2, 2-3, and 2-6).

Power connection

2

3

2

3

2

2

100-240V

50/60 Hz 0.5A

IN

OUT

INPUT 1

IN

OUT

INPUT 2

ININ

OUTOUT

INPUT 3

INPUT 4

1

4

5

4

5

4

4

Figure 2-2 — Power, video input, and buffered video outputs

1AC power connector — Plug a standard IEC power cord into this connector to connect the switcher to a 100 to 240VAC, 50 Hz or 60 Hz power source.

Video input and output connections

2

3

4

5

Input 1, Input 2, Input 3, and Input 4, composite video inputs — Connect

composite video inputs to these BNC connectors.

Input 1 and Input 2, S-video inputs — Connect S-video inputs to these 4-pin mini-DIN connectors. If both composite video and S-video are connected to Input 1 or Input 2, the switcher can autoselect the active line if the input has been configured as “Auto”. See Advanced Menus and the Input video type section in chapter 3. If both lines are active, S-video is selected.

Input 1, Input 2, Input 3, and Input 4, composite video buffered outputs

These BNC connectors output unswitched bufferd loops of the composite video input. The buffered output loops are always active, independent of autoselection. See Advanced Menus and the Input video type section in chapter 3.

Input 1 and Input 2, S-video buffered outputs — These 4-pinmini-DIN connectors output unswitched buffered loops of the S-video input. The buffered output loops are always active, independent of autoselection. See Advanced Menus and the Input video type section in chapter 3.

SVS 100 Installation

2-3

Image 13
Contents SVS Seamless Video SwitcherSafety Instructions English PrecautionsConsignes de Sécurité Français Sicherheitsanleitungen DeutschQuick Start SVS Connecting the SVSRack or Table/Wall Mounting Effects InputGenlock Picture ControlsTable of Contents Table of Contents, cont’d Introduction OneAbout the SVS IntroductionSVS 100 Introduction Four Ntsc or PAL video inputs SVS 100 FeaturesIntroduction, cont’d Two InstallationSVS 100 Installation InstallationMounting the SVS Table or wall mountingCabling and Rear Panel Views Power connectionRack mounting Video input and output connectionsAudio input and output connections Installation, cont’dGenlock connections Genlock and Vertical Interval SwitchingRS-232/RS-422 connection Genlock setup Superimposed waveforms Oscilloscope displaysVectorscope screen during horizontal phase adjustment Operation ThreeInput selection controls and indicators Front Panel Controls and IndicatorsOperation SVS 100 OperationExamples of switching effects Effects controls and indicatorsOperation, cont’d Picture controls and indicators Genlock controls and indicatorsEncoder knob Audio buttonSystem Reset Executive ModeDemo mode Advanced MenusVCR mode Audio switching methodInput video type Optimizing the Video and Audio Inputs Chroma settingOperation, cont’d Windows-based Control Program FourUsing the Software Installing the Windows-based Control SoftwareWindows-based Control Program SVS 100 Windows-based Control ProgramHelp Windows-based Control Program, cont’d Serial Communication FiveSerial Communication Remote Control Port RS-232/RS-422Host-to-SVS 100 Communication SVS 100 Serial CommunicationUsing the command/response table Serial Communication, cont’d Audio Switch Mode SVS 100 Communication Example responses to commandsReference Information AAppendixReference Information Saving and Recalling Input Configuration PresetsSpecial Applications SVS 100 AppendixRemoving the top cover Configuring the SVS 100 for RS-422Replacing the top cover Relocating the ribbon cable and setting the jumperSVS 100 Appendix Video input and loopout Specifications SVSGeneral SVS 100 Appendix FCC Class a Notice Extron’s Warranty Extron Electronics. All rights reserved
Related manuals
Manual 2 pages 10.59 Kb