Extron electronic SVS 100 manual Quick Start SVS, Rack or Table/Wall Mounting, Connecting the SVS

Page 3

Quick Start — SVS 100

Installation

Step 1

Turn off power to the SVS 100 and all other devices that will be connected.

two mounting screws on each side

rack-mount bracket

Drill pilot holes — 3/32” (2.4mm) diam. 1/4” (6.3 mm) deep

Step 2

If the SVS 100 is to be rack or table/wall mounted, position the brackets and insert the mounting screws, as shown on the right.

Step 3

Using Inputs 1, 2, 3, and 4, attach up to four composite/S-video input devices to the SVS 100. Inputs 1 and 2 can either be composite video or S-video, inputs 3 and 4 are composite video only.

or

 

table/

four #8 screws

wall-mount

on each side

bracket

Rack or Table/Wall Mounting

 

 

 

 

 

 

 

GENLOCK

 

IN

IN

 

 

 

 

 

IN

OUT

 

 

IN

IN

A

INPUTS

OUTPUT

 

 

 

 

 

RS-232/422

 

OUT

OUT

 

 

 

L 1 R L 2 R L 3 R L 4 R

L 1 R

 

 

 

 

 

 

 

 

 

 

 

OUT

OUT

B

C

 

 

 

INPUT 1

INPUT 2

INPUT 3

INPUT 4

OUTPUT

 

 

REMOTE

 

Any inputs must be either all NTSC or

all PAL, they cannot be both.

The buffered loopout connectors for all inputs may be used to output the identical signal to other devices. See the application connection diagram on the right.

Step 4

Connect up to three output devices to the SVS 100 using composite video output A, composite video output B, and S-video output C.

Step 5

For stereo audio input, connect up to four audio sources to audio inputs 1, 2, 3, and 4. See the Audio input and output connections section in chapter 2 for illustrations and warnings.

Step 6

For stereo audio output, connect an audio output device to the 3.5 mm stereo audio output connector. See the Audio input and output connections section in chapter 2 for illustrations and warnings.

Step 7

If the SVS 100 is to be connected to a computer or host controller for remote control, connect the host’s RS-232/RS-422 cable to the 9-pin female RS-232/RS-422 remote connector of the SVS 100. For an RS-232/RS-422 pinout table, see the Remote Control Port (RS-232/RS-422)section in chapter 5.

PC Computer

VSC 150

RS-232 Control

Videoconferencing System

SVS 100

LCD Projector

Video Camera

VCR

Document Camera

VCR

Connecting the SVS 100

The SVS 100 comes from the factory already configured for RS-232. To set the SVS 100 for RS-422 operation, see “Configuring the SVS 100 for RS-422” in the Appendix.

Step 8

If a genlock device is to be connected to the

SVS 100, see Genlock and Vertical Interval Switching in chapter 2.

Step 9

Power up the input and output devices, then connect power to the SVS 100. A summary of the front panel controls is described on the following page. See the appropriate chapters in this manual for further details.

Image 3
Contents SVS Seamless Video SwitcherSicherheitsanleitungen Deutsch PrecautionsSafety Instructions English Consignes de Sécurité FrançaisConnecting the SVS Quick Start SVSRack or Table/Wall Mounting Picture Controls InputEffects GenlockTable of Contents Table of Contents, cont’d Introduction OneIntroduction About the SVSSVS 100 Introduction Four Ntsc or PAL video inputs SVS 100 FeaturesIntroduction, cont’d Two InstallationTable or wall mounting InstallationSVS 100 Installation Mounting the SVSVideo input and output connections Power connectionCabling and Rear Panel Views Rack mountingAudio input and output connections Installation, cont’dGenlock and Vertical Interval Switching Genlock connectionsRS-232/RS-422 connection Genlock setup Superimposed waveforms Oscilloscope displaysVectorscope screen during horizontal phase adjustment Operation ThreeSVS 100 Operation Front Panel Controls and IndicatorsInput selection controls and indicators OperationExamples of switching effects Effects controls and indicatorsOperation, cont’d Picture controls and indicators Genlock controls and indicatorsEncoder knob Audio buttonAdvanced Menus Executive ModeSystem Reset Demo modeAudio switching method VCR modeInput video type Optimizing the Video and Audio Inputs Chroma settingOperation, cont’d Windows-based Control Program FourSVS 100 Windows-based Control Program Installing the Windows-based Control SoftwareUsing the Software Windows-based Control ProgramHelp Windows-based Control Program, cont’d Serial Communication FiveSVS 100 Serial Communication Remote Control Port RS-232/RS-422Serial Communication Host-to-SVS 100 CommunicationUsing the command/response table Serial Communication, cont’d Audio Switch Mode SVS 100 Communication Example responses to commandsReference Information AAppendixSVS 100 Appendix Saving and Recalling Input Configuration PresetsReference Information Special ApplicationsRemoving the top cover Configuring the SVS 100 for RS-422Replacing the top cover Relocating the ribbon cable and setting the jumperSVS 100 Appendix Video input and loopout Specifications SVSGeneral SVS 100 Appendix FCC Class a Notice Extron’s Warranty Extron Electronics. All rights reserved
Related manuals
Manual 2 pages 10.59 Kb