Extron electronic manual Installing labels in the System 7SC’s buttons

Page 28

Installation, cont’d

Each button label can contain from 1 to 3 lines of text (or none) with choices for each line of different font sizes and whether to center or left justify the text.

Each button label can also contain a picture (or none) selected either from the Device Palette or a user-supplied graphic file. User-supplied graphics should be icon (.ICO) or bitmap (.BMP) files. Files

SCP 250 button label screencalled TEST.BMP and DEMO_BTN.DAT are installed

with this program as examples, and a help file is also included.

Installing labels in the System 7SC’s buttons

Label installation for the SCPs is covered in the SCP/AAP A, SCP 200, SCP 250 User’s Manual. Use the following procedure to install new labels in the System 7SC’s front panel buttons.

1. Remove the button from the switcher: grasp the button firmly and pull it away from the front panel.

2.Separate the gray backing from the clear plastic cap by inserting a flat blade screwdriver into the slots and twisting

it, as shown at right.

Screwdriver

3. Save the translucent, white backing plate, but remove the text insert.

4.Make new labels by using the Button-Label Generator software (see pages 2-14 and 2-15). Print and cut them out.

5. Insert a button label and the white backing plate into the cap and reassemble the button. Press the cap onto

the gray backing gently but firmly.

6. Press the button into place in the switcher.

2-16 System 7SC • Installation

Image 28

Contents System Switcher System 7SCSafety Instructions English Consignes de Sécurité FrançaisSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolTable of Contents Table of Contents, cont’d System 7SC Table of Contents Iii Iv System 7SC Table of Contents One What is the System 7SC? About this ManualAbout the System 7SC Typical System 7SC applicationControlling the switcher and an A/V system Features Features and OptionsMHz -3 dB video bandwidth Configurable video inputs Options and accessories Introduction, cont’d Two Mounting the Switcher Cabling and Panel ViewsTabletop use Rack mountingSystem 7SC Front Panel Power, video, and audio conections Front panel inputsRear panel inputs Captive screw connector wiring for rear panel audio inputs OutputsAudio inputs Control device connections RGBIR communications port IR Comm IR Communications port wiring options For the IR Emitter onlyUC 50, 100, 200 Cable Color Codes Connecting and Slaving a Switcher System 7SC master connected to a slaved switcher System 7SC Rear PanelExample of input numbering with a six-input slaved switcher Labeling Buttons on the System 7SC and SCPsInstalling the software Using the softwareButton-Label Generator software System 7SC button label screen SCP 200 button label screenInstalling labels in the System 7SC’s buttons Three Control features Front Panel Features and Basic OperationSystem 7SC Operation and Configuration Mode button Display Power buttonDisplay Mute button Operation and Configuration, cont’d Adjustment featuresMiscellaneous features Input selection featuresDisplay command indicator LEDs IR and RS-232 Projector Control Projector control memoryProjector control memory usage ExampleSetting up a DVD source Optimizing the SystemMenus, Configuration, and Adjustments Moving through menus by using front panel controlsDefault menus Menu overviewSwitcher Setup/Configuration Scaler Polarity +/V+Scaler Rate resolution and refresh rate RGB Delay Triple-Action SwitchingScaler Sync RGB format Scaler Polarity sync polaritySystem 7SC with a slaved switcher Add Slave slaving switchersEdge Smoothing Audio/Video Adjustments Input Configuration signal formatBlank Input blanking adjustment Audio LevelImage Size Size InputIR Learning Configuration Navigating through the IR Learning Configuration menuClearing IR commands from memories Clearing IR commands from a button’s memoryInitiating IR learning Initiating IR learningImage adjustments Reset to Default clearing settings and adjustmentsGlobal system reset Information/System OptionsInput you wish to adjust Executive mode front panel lockoutCentering Enabling and disabling executive mode Remote Control of the System 7SCSCP control pads IR 701 infrared remote control Selecting an inputFour Host-to-switcher communications Switcher-initiated messagesError responses RS-232 Programmer’s GuideSymbol definitions Using the command/response tablesAscii to Hex conversion table Command Ascii Command Response Additional description Video configuration Detail modeColor TintImage size Horizontal sizeVertical size Top blankingZap reset to default settings Executive mode front panel lockoutFirmware version, part number & information requests Command Ascii Command Response Values Delay timesScaler settings Room relaysIR-related settings Audio settingsMiscellaneous settings Command Hex. command Response Additional description Send/receive data to/from page 0 memorySend/receive data to/from page 1 memory Send/receive a flag parameter blockInstalling the software Using the control programMini Mode Control Software for WindowsSpecial features User ModeConfiguration Real Time Adjustments Projector Driver Saving and restoring configurations Room & Misc. OptionsDownloading and using projector drivers Using the help programKey to file names File name Description AAppendix a Specifications System 7SC Reference MaterialSync Reference Material, cont’d Part Numbers and Accessories AccessoriesIncluded parts Replacement Part number Accessories Part numberFirmware Upgrade Installation Align NotchesSystem 7SC Reference Material Glossary FCC Class a Notice Extron’s Warranty Asia JapanExtron Electronics, USA