Extron electronic System 7SC manual Projector Driver

Page 62

Serial Communication, cont’d

Projector Driver

The Projector Driver screen displays the current IR and RS-232 parameters and commands. Commands and drivers can be loaded, entered (programmed), or edited from this screen. Using this screen, commands can be associated with each input selection, display/projector control, or room button.

Special features

All of the items found in this screen are only available in this part of the control program. There is no other way to perform these functions. After loading a projector driver, but before editing or programming RS-232 commands, click on the button (such as Room 1 or Power Off in the upper part of the Projector Driver screen) that you wish to edit or program. The System 7SC Help program provides step-by-step directions for programming buttons.

Load New Driver — Select this button to load a new, Extron-created projector driver file into the System 7SC and into the control program. Alternatively, you can select the Load New Driver From... option in the File menu.

Remove IR/232 — Clicking on this option will erase the IR and RS-232 commands that are stored in the memory for the selected button.

Page 0 sends — This feature shows what type of commands (IR, RS-232, or none) the button is programmed to send. Choose RS-232 if you wish to program unidirectional RS-232 commands for the selected button.

RS-232Uni-directional Commands — The location and hexadecimal and ASCII forms of any unidirectional RS-232 commands that have been programmed into the selected key will be displayed in this area. Commands and command length can also be entered or edited in this area. Refer to the System 7SC Help program for complete step-by-step programming directions.

IR/RS-232 params — This section shows parameter information about the command stored in memory for the selected button.

4-14 System 7SC • Serial Communication

Image 62

Contents System Switcher System 7SCSicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolTable of Contents Table of Contents, cont’d System 7SC Table of Contents Iii Iv System 7SC Table of Contents One About the System 7SC What is the System 7SC?About this Manual Typical System 7SC applicationControlling the switcher and an A/V system MHz -3 dB video bandwidth Configurable video inputs Features and OptionsFeatures Options and accessories Introduction, cont’d Two Tabletop use Mounting the SwitcherCabling and Panel Views Rack mountingSystem 7SC Front Panel Power, video, and audio conections Front panel inputsRear panel inputs Captive screw connector wiring for rear panel audio inputs OutputsAudio inputs Control device connections RGBIR communications port IR Comm IR Communications port wiring options For the IR Emitter onlyUC 50, 100, 200 Cable Color Codes Connecting and Slaving a Switcher System 7SC master connected to a slaved switcher System 7SC Rear PanelExample of input numbering with a six-input slaved switcher Labeling Buttons on the System 7SC and SCPsButton-Label Generator software Installing the softwareUsing the software System 7SC button label screen SCP 200 button label screenInstalling labels in the System 7SC’s buttons Three System 7SC Operation and Configuration Front Panel Features and Basic OperationControl features Display Mute button Display Power buttonMode button Operation and Configuration, cont’d Adjustment featuresDisplay command indicator LEDs Input selection featuresMiscellaneous features Projector control memory usage IR and RS-232 Projector ControlProjector control memory ExampleSetting up a DVD source Optimizing the SystemDefault menus Menus, Configuration, and AdjustmentsMoving through menus by using front panel controls Menu overviewSwitcher Setup/Configuration Scaler Polarity +/V+Scaler Sync RGB format Scaler Rate resolution and refresh rateRGB Delay Triple-Action Switching Scaler Polarity sync polarityEdge Smoothing Add Slave slaving switchersSystem 7SC with a slaved switcher Audio/Video Adjustments Input Configuration signal formatImage Size Blank Input blanking adjustmentAudio Level Size InputIR Learning Configuration Navigating through the IR Learning Configuration menuClearing IR commands from memories Clearing IR commands from a button’s memoryInitiating IR learning Initiating IR learningGlobal system reset Image adjustmentsReset to Default clearing settings and adjustments Information/System OptionsCentering Executive mode front panel lockoutInput you wish to adjust SCP control pads Remote Control of the System 7SCEnabling and disabling executive mode IR 701 infrared remote control Selecting an inputFour Error responses Host-to-switcher communicationsSwitcher-initiated messages RS-232 Programmer’s GuideAscii to Hex conversion table Using the command/response tablesSymbol definitions Command Ascii Command Response Additional description Color Video configurationDetail mode TintVertical size Image sizeHorizontal size Top blankingFirmware version, part number & information requests Executive mode front panel lockoutZap reset to default settings Scaler settings Command Ascii Command Response ValuesDelay times Room relaysMiscellaneous settings Audio settingsIR-related settings Send/receive data to/from page 1 memory Command Hex. command Response Additional descriptionSend/receive data to/from page 0 memory Send/receive a flag parameter blockMini Mode Installing the softwareUsing the control program Control Software for WindowsConfiguration User ModeSpecial features Real Time Adjustments Projector Driver Saving and restoring configurations Room & Misc. OptionsKey to file names File name Description Using the help programDownloading and using projector drivers AAppendix a Specifications System 7SC Reference MaterialSync Reference Material, cont’d Included parts Replacement Part number Part Numbers and AccessoriesAccessories Accessories Part numberFirmware Upgrade Installation Align NotchesSystem 7SC Reference Material Glossary FCC Class a Notice Extron’s Warranty Asia JapanExtron Electronics, USA