Extron electronic System 7SC manual Clearing IR commands from memories

Page 43

Clearing IR commands from memories

The memory for each Display, Room, or input selection button can either be clear (empty, no stored commands are associated with the button) or saved (containing an IR command that is saved in nonvolatile memory). To clear IR commands from a button’s memory:

1.

2.

3.

4.

5.

Extron

System 7SC

MENU

SWITCHER SETUP/ CONFIGURATION

MENU

From the main menu press the Menu button until the IR Learning Configuration menu appears.

Scroll through the submenu to the desired button by pressing the Next button.

Rotate the Adjust knob () to toggle from the button’s status to the Clear command.

Press the Next button to clear the IR commands from that Display, Room, or input selection button’s memory.

Press Next to scroll to another button, or press Menu or allow the System 7 to time out to the main screen.

AUDIO/VIDEO

ADJUSTMENTS

MENU

IR LEARNING

CONFIGURATION

NEXT

From any screen in

this submenu, press MENU to go to the IR LEARNING menu.

Display Power: On

Status: Saved

Display Power: On

Learn?

Display Power: On		NEXT
Clear?		NEXT
Clear?

									Scrolls through
					Display Power: Off				buttons that
NEXT					Display Power: Off		NEXT		can have
NEXT					Status: Saved		NEXT		can have
					Status: Saved				associated
									associated
									IR commands

	Display Power: On	Display Power: On	NEXT
	Clearing IR!	Status: Clear

The button's IR

codes have been

cleared from

memory.

Clearing IR commands from a button’s memory

System 7SC • Operation and Configuration 3-15

Image 43

Contents System 7SC System SwitcherInstrucciones de seguridad Español Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschTable of Contents Table of Contents, cont’d System 7SC Table of Contents Iii Iv System 7SC Table of Contents One Typical System 7SC application What is the System 7SC?About this Manual About the System 7SCControlling the switcher and an A/V system Features Features and OptionsMHz -3 dB video bandwidth Configurable video inputs Options and accessories Introduction, cont’d Two Rack mounting Mounting the SwitcherCabling and Panel Views Tabletop useSystem 7SC Front Panel Front panel inputs Power, video, and audio conectionsRear panel inputs Outputs Captive screw connector wiring for rear panel audio inputsAudio inputs RGB Control device connectionsIR communications port IR Comm For the IR Emitter only IR Communications port wiring optionsUC 50, 100, 200 Cable Color Codes Connecting and Slaving a Switcher System 7SC Rear Panel System 7SC master connected to a slaved switcherLabeling Buttons on the System 7SC and SCPs Example of input numbering with a six-input slaved switcherSystem 7SC button label screen SCP 200 button label screen Installing the softwareUsing the software Button-Label Generator softwareInstalling labels in the System 7SC’s buttons Three Control features Front Panel Features and Basic OperationSystem 7SC Operation and Configuration Mode button Display Power buttonDisplay Mute button Adjustment features Operation and Configuration, cont’dMiscellaneous features Input selection featuresDisplay command indicator LEDs Example IR and RS-232 Projector ControlProjector control memory Projector control memory usageOptimizing the System Setting up a DVD sourceMenu overview Menus, Configuration, and AdjustmentsMoving through menus by using front panel controls Default menusScaler Polarity +/V+ Switcher Setup/ConfigurationScaler Polarity sync polarity Scaler Rate resolution and refresh rateRGB Delay Triple-Action Switching Scaler Sync RGB formatSystem 7SC with a slaved switcher Add Slave slaving switchersEdge Smoothing Input Configuration signal format Audio/Video AdjustmentsSize Input Blank Input blanking adjustmentAudio Level Image SizeNavigating through the IR Learning Configuration menu IR Learning ConfigurationClearing IR commands from a button’s memory Clearing IR commands from memoriesInitiating IR learning Initiating IR learningInformation/System Options Image adjustmentsReset to Default clearing settings and adjustments Global system resetInput you wish to adjust Executive mode front panel lockoutCentering Enabling and disabling executive mode Remote Control of the System 7SCSCP control pads Selecting an input IR 701 infrared remote controlFour RS-232 Programmer’s Guide Host-to-switcher communicationsSwitcher-initiated messages Error responsesSymbol definitions Using the command/response tablesAscii to Hex conversion table Command Ascii Command Response Additional description Tint Video configurationDetail mode ColorTop blanking Image sizeHorizontal size Vertical sizeZap reset to default settings Executive mode front panel lockoutFirmware version, part number & information requests Room relays Command Ascii Command Response ValuesDelay times Scaler settingsIR-related settings Audio settingsMiscellaneous settings Send/receive a flag parameter block Command Hex. command Response Additional descriptionSend/receive data to/from page 0 memory Send/receive data to/from page 1 memoryControl Software for Windows Installing the softwareUsing the control program Mini ModeSpecial features User ModeConfiguration Real Time Adjustments Projector Driver Room & Misc. Options Saving and restoring configurationsDownloading and using projector drivers Using the help programKey to file names File name Description AAppendix a System 7SC Reference Material SpecificationsSync Reference Material, cont’d Accessories Part number Part Numbers and AccessoriesAccessories Included parts Replacement Part numberAlign Notches Firmware Upgrade InstallationSystem 7SC Reference Material Glossary Asia Japan FCC Class a Notice Extron’s WarrantyExtron Electronics, USA