Extron electronic System 7SC manual Switcher Setup/Configuration, Scaler Polarity +/V+

Page 37

Switcher Setup/Configuration

The flowchart below provides an overview of the Switcher Setup/Configuration submenu and the options for each setting.

Extron

System 7SC

MENU

SWITCHER SETUP/ CONFIGURATION

NEXT

Scaler Rate

1280X1024, 60 Hz

NEXT

Scaler Sync

RGsB

NEXT

Scaler Polarity

H+/V+

NEXT

Scaler output rates

•See the table on the next page for available combinations of resolutions and refresh rates.

Default: 640x480, 60 Hz

NOTE Lock = Accu-RATE Frame Lock™

Sync formats

Polarity combinations

• RGBHV (default)

•

H-/V- (default)

•

H+/V-

• RGBS

•

H-/V+

•

H+/V+

• RGsB

 

 

 

 

RGB Delay

1.5 Sec.

Delay time (in seconds)

•0.0 (default) up to

•5.0

in 0.5 sec. increments

NEXT

Scaler Blue Out?

(No) Yes

Display blue & sync only

•No (default)

•Yes

NEXT

Edge Smoothing?

No (Yes)

Smooth edges

•No

•Yes (default)

NEXT

Add Slave

No Slave Swr

NEXT

Autoselect # 07

No (Yes)

NEXT

Room1 Relay Cnfg

Toggle On/Off

NEXT

Add a slave switcher on input 1

• No Slave Swr (default)

...or select a slave switcher input quantity:

•8 Input Slave

•10 Input Slave

•6 Input Slave

•4 Input Slave

Autoselect the input signal format for the front panel input

•No

•Yes (default)

RGB input has priority over S-video & composite video if all formats are active.

Configure the Room 1 relay

•Toggle On/Off (default) – Latching mode. The relay remains open or closed until the button is pressed again.

•X.XXX Sec – Momentary mode. The relay is open or closed for a set time, adjustable from 0.250 seconds to 2.000 seconds in 0.125 second increments.

Room2 Relay Cnfg

 

NEXT

1.375 Sec

 

 

 

 

 

 

Configure the Room 2 relay

•Toggle On/Off (default) – Latching mode. The relay remains open or closed until the button is pressed again.

•X.XXX Sec – Momentary mode. The relay is open or closed for a set time, adjustable from 0.250 seconds to 2.000 seconds in 0.125 second increments.

2:2 Pulldown

 

NEXT

Input#01 : Off

 

 

 

 

 

 

Turn 2:2 Pulldown On/Off (per input)

•On – Select this to activate 2:2 film detection for the selected input to maximize image detail and sharpness for for PAL source material that originated from film.

•Off (default) – 2:2 detection is off.

If you press the Menu button while a submenu is active, the next main menu will become active. For example, the menu will change from the Switcher Setup/Configuration menu or submenus to the Audio/Video Adjustments main menu.

To return to the default screens, let the System 7SC time-out for 8 seconds, or press the Menu button until the Exit? menu appears, then press the Next button.

System 7SC • Operation and Configuration

3-9

Page 36 Page 38
Image 37
Page 36 Page 38
Contents System 7SC System SwitcherConsignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolTable of Contents Table of Contents, cont’d System 7SC Table of Contents Iii Iv System 7SC Table of Contents One About this Manual What is the System 7SC?About the System 7SC Typical System 7SC applicationControlling the switcher and an A/V system Features Features and OptionsMHz -3 dB video bandwidth Configurable video inputs Options and accessories Introduction, cont’d Two Cabling and Panel Views Mounting the SwitcherTabletop use Rack mountingSystem 7SC Front Panel Front panel inputs Power, video, and audio conectionsRear panel inputs Outputs Captive screw connector wiring for rear panel audio inputsAudio inputs RGB Control device connectionsIR communications port IR Comm For the IR Emitter only IR Communications port wiring optionsUC 50, 100, 200 Cable Color Codes Connecting and Slaving a Switcher System 7SC Rear Panel System 7SC master connected to a slaved switcherLabeling Buttons on the System 7SC and SCPs Example of input numbering with a six-input slaved switcherUsing the software Installing the softwareButton-Label Generator software System 7SC button label screen SCP 200 button label screenInstalling labels in the System 7SC’s buttons Three Control features Front Panel Features and Basic OperationSystem 7SC Operation and Configuration Mode button Display Power buttonDisplay Mute button Adjustment features Operation and Configuration, cont’dMiscellaneous features Input selection featuresDisplay command indicator LEDs Projector control memory IR and RS-232 Projector ControlProjector control memory usage ExampleOptimizing the System Setting up a DVD sourceMoving through menus by using front panel controls Menus, Configuration, and AdjustmentsDefault menus Menu overviewScaler Polarity +/V+ Switcher Setup/ConfigurationRGB Delay Triple-Action Switching Scaler Rate resolution and refresh rateScaler Sync RGB format Scaler Polarity sync polaritySystem 7SC with a slaved switcher Add Slave slaving switchersEdge Smoothing Input Configuration signal format Audio/Video AdjustmentsAudio Level Blank Input blanking adjustmentImage Size Size InputNavigating through the IR Learning Configuration menu IR Learning ConfigurationClearing IR commands from a button’s memory Clearing IR commands from memoriesInitiating IR learning Initiating IR learningReset to Default clearing settings and adjustments Image adjustmentsGlobal system reset Information/System OptionsInput you wish to adjust Executive mode front panel lockoutCentering Enabling and disabling executive mode Remote Control of the System 7SCSCP control pads Selecting an input IR 701 infrared remote controlFour Switcher-initiated messages Host-to-switcher communicationsError responses RS-232 Programmer’s GuideSymbol definitions Using the command/response tablesAscii to Hex conversion table Command Ascii Command Response Additional description Detail mode Video configurationColor TintHorizontal size Image sizeVertical size Top blankingZap reset to default settings Executive mode front panel lockoutFirmware version, part number & information requests Delay times Command Ascii Command Response ValuesScaler settings Room relaysIR-related settings Audio settingsMiscellaneous settings Send/receive data to/from page 0 memory Command Hex. command Response Additional descriptionSend/receive data to/from page 1 memory Send/receive a flag parameter blockUsing the control program Installing the softwareMini Mode Control Software for WindowsSpecial features User ModeConfiguration Real Time Adjustments Projector Driver Room & Misc. Options Saving and restoring configurationsDownloading and using projector drivers Using the help programKey to file names File name Description AAppendix a System 7SC Reference Material SpecificationsSync Reference Material, cont’d Accessories Part Numbers and AccessoriesIncluded parts Replacement Part number Accessories Part numberAlign Notches Firmware Upgrade InstallationSystem 7SC Reference Material Glossary Asia Japan FCC Class a Notice Extron’s WarrantyExtron Electronics, USA
Top Page Image Contents