Extron electronic System 7SC manual Button-Label Generator software, Installing the software

Page 27

Button-Label Generator software

The Extron Button-Label Generator program (Buttons.exe) is included with the System 7SC, and it can also be downloaded from the Extron Web site (http://www.extron.com). This program is used to create and print labels that can be inserted into the illuminated pushbuttons or placed in slots above/below buttons on the SCPs and on various Extron switchers.

Installing the software

This program is installed at the same time the System 7SC control program is installed. No additional steps are required. See page 4-11 of this manual for installation instructions.

Using the software

1.To run the Button-Label Generator program, double-click on the Button-Label Generator icon (shown at left) in the Extron Electronics group or folder, and click OK when prompted.

2.Under System selection, choose the item that corresponds to the device for which you want to make labels: System 7SC, SCP 200, or SCP 250. The button label editing area changes to reflect the number and arrangement of buttons on the device.

3.Using normal Windows controls, you can create and print labels that can be cut out and placed in the label windows on the front panel of the switcher.

For information about using the program, you can access a help file by clicking on the Help menu on the main screen and choosing Show Help.

You can also see an example of a completed Extron’s Button-Label Generator window by clicking on the Help menu on the main screen, choosing Show Help, and clicking on the Load Demo button.

The following pictures are examples of what the Button-Label Generator screens look like when set for the System 7SC, the SCP 200, and SCP 250.

System 7SC button label screen

SCP 200 button label screen

System 7SC • Installation 2-15

Image 27

Contents System 7SC System SwitcherInstrucciones de seguridad Español Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschTable of Contents Table of Contents, cont’d System 7SC Table of Contents Iii Iv System 7SC Table of Contents One Typical System 7SC application What is the System 7SC?About this Manual About the System 7SCControlling the switcher and an A/V system Features and Options FeaturesMHz -3 dB video bandwidth Configurable video inputs Options and accessories Introduction, cont’d Two Rack mounting Mounting the SwitcherCabling and Panel Views Tabletop useSystem 7SC Front Panel Front panel inputs Power, video, and audio conectionsRear panel inputs Outputs Captive screw connector wiring for rear panel audio inputsAudio inputs RGB Control device connectionsIR communications port IR Comm For the IR Emitter only IR Communications port wiring optionsUC 50, 100, 200 Cable Color Codes Connecting and Slaving a Switcher System 7SC Rear Panel System 7SC master connected to a slaved switcherLabeling Buttons on the System 7SC and SCPs Example of input numbering with a six-input slaved switcherSystem 7SC button label screen SCP 200 button label screen Installing the softwareUsing the software Button-Label Generator softwareInstalling labels in the System 7SC’s buttons Three Front Panel Features and Basic Operation Control featuresSystem 7SC Operation and Configuration Display Power button Mode buttonDisplay Mute button Adjustment features Operation and Configuration, cont’dInput selection features Miscellaneous featuresDisplay command indicator LEDs Example IR and RS-232 Projector ControlProjector control memory Projector control memory usageOptimizing the System Setting up a DVD sourceMenu overview Menus, Configuration, and AdjustmentsMoving through menus by using front panel controls Default menusScaler Polarity +/V+ Switcher Setup/ConfigurationScaler Polarity sync polarity Scaler Rate resolution and refresh rateRGB Delay Triple-Action Switching Scaler Sync RGB formatAdd Slave slaving switchers System 7SC with a slaved switcherEdge Smoothing Input Configuration signal format Audio/Video AdjustmentsSize Input Blank Input blanking adjustmentAudio Level Image SizeNavigating through the IR Learning Configuration menu IR Learning ConfigurationClearing IR commands from a button’s memory Clearing IR commands from memoriesInitiating IR learning Initiating IR learningInformation/System Options Image adjustmentsReset to Default clearing settings and adjustments Global system resetExecutive mode front panel lockout Input you wish to adjustCentering Remote Control of the System 7SC Enabling and disabling executive modeSCP control pads Selecting an input IR 701 infrared remote controlFour RS-232 Programmer’s Guide Host-to-switcher communicationsSwitcher-initiated messages Error responsesUsing the command/response tables Symbol definitionsAscii to Hex conversion table Command Ascii Command Response Additional description Tint Video configurationDetail mode ColorTop blanking Image sizeHorizontal size Vertical sizeExecutive mode front panel lockout Zap reset to default settingsFirmware version, part number & information requests Room relays Command Ascii Command Response ValuesDelay times Scaler settingsAudio settings IR-related settingsMiscellaneous settings Send/receive a flag parameter block Command Hex. command Response Additional descriptionSend/receive data to/from page 0 memory Send/receive data to/from page 1 memoryControl Software for Windows Installing the softwareUsing the control program Mini ModeUser Mode Special featuresConfiguration Real Time Adjustments Projector Driver Room & Misc. Options Saving and restoring configurationsUsing the help program Downloading and using projector driversKey to file names File name Description AAppendix a System 7SC Reference Material SpecificationsSync Reference Material, cont’d Accessories Part number Part Numbers and AccessoriesAccessories Included parts Replacement Part numberAlign Notches Firmware Upgrade InstallationSystem 7SC Reference Material Glossary Asia Japan FCC Class a Notice Extron’s WarrantyExtron Electronics, USA