Extron electronic System 7SC Information/System Options, Image adjustments, Global system reset

Page 45

Information/System Options

The Information/System Options menu provides information on the System 7SC (firmware version and part number) and on the projector and driver. The switcher can also be reset to factory default settings via this menu.

Extron

System 7SC

MENU

SWITCHER SETUP/ CONFIGURATION

MENU

AUDIO/VIDEO

ADJUSTMENTS

MENU

IR LEARNING

CONFIGURATION

MENU

INFORMATION SYSTEM/OPTIONS

NEXT

Sys 7SC VerX.XX

PN 60-340-01

NEXT

No Driver

No Version

Projector and driver information

Drivername or Custom Version of the driver

SHARP XGNV6XU

IR Rev CUSTOM

NEXT			Reset to Default
NEXT			Press Menu&Next
			Press Menu&Next


				MENU
			4 sec.	NEXT
				NEXT


			Confirm Reset
			Press Menu&Next

MENU

NEXT

Please Wait

Resetting System

NEXT

NEXT

Reset to Default (clearing settings and adjustments)

Resetting the System 7SC clears all the user-made settings and adjustments from the System 7’s memory and replaces them with the factory default settings. This includes settings for audio level, color, tint, brightness, contrast, detail, and centering. All inputs will be reset to RGB input.

When the system is reset, the IR and RS-232 commands and drivers will remain in memory.

Global system reset

A global system reset clears and resets all of the System 7SC’s settings, including the settings/adjustments discussed above and all programming, IR and RS-232 commands, and drivers. To perform a global reset, press and hold the Menu and Next keys while connecting the System 7 to an AC power source.

Image adjustments

All the image adjustments are stored in memory and can be set separately for each input. Image adjustments apply to scaled video output only; RGB signals are passed through without adjustments.

Color, tint, brightness, contrast, detail

To adjust an image for color, tint, brightness, contrast, or detail, follow the steps on the next page. An illustration of making color adjustments shows the process, which is the same for all the image adjustments.

System 7SC • Operation and Configuration 3-17

Image 45

Contents System 7SC System SwitcherConsignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolTable of Contents Table of Contents, cont’d System 7SC Table of Contents Iii Iv System 7SC Table of Contents One About this Manual What is the System 7SC?About the System 7SC Typical System 7SC applicationControlling the switcher and an A/V system Features and Options FeaturesMHz -3 dB video bandwidth Configurable video inputs Options and accessories Introduction, cont’d Two Cabling and Panel Views Mounting the SwitcherTabletop use Rack mountingSystem 7SC Front Panel Front panel inputs Power, video, and audio conectionsRear panel inputs Outputs Captive screw connector wiring for rear panel audio inputsAudio inputs RGB Control device connectionsIR communications port IR Comm For the IR Emitter only IR Communications port wiring optionsUC 50, 100, 200 Cable Color Codes Connecting and Slaving a Switcher System 7SC Rear Panel System 7SC master connected to a slaved switcherLabeling Buttons on the System 7SC and SCPs Example of input numbering with a six-input slaved switcherUsing the software Installing the softwareButton-Label Generator software System 7SC button label screen SCP 200 button label screenInstalling labels in the System 7SC’s buttons Three Front Panel Features and Basic Operation Control featuresSystem 7SC Operation and Configuration Display Power button Mode buttonDisplay Mute button Adjustment features Operation and Configuration, cont’dInput selection features Miscellaneous featuresDisplay command indicator LEDs Projector control memory IR and RS-232 Projector ControlProjector control memory usage ExampleOptimizing the System Setting up a DVD sourceMoving through menus by using front panel controls Menus, Configuration, and AdjustmentsDefault menus Menu overviewScaler Polarity +/V+ Switcher Setup/ConfigurationRGB Delay Triple-Action Switching Scaler Rate resolution and refresh rateScaler Sync RGB format Scaler Polarity sync polarityAdd Slave slaving switchers System 7SC with a slaved switcherEdge Smoothing Input Configuration signal format Audio/Video AdjustmentsAudio Level Blank Input blanking adjustmentImage Size Size InputNavigating through the IR Learning Configuration menu IR Learning ConfigurationClearing IR commands from a button’s memory Clearing IR commands from memoriesInitiating IR learning Initiating IR learningReset to Default clearing settings and adjustments Image adjustmentsGlobal system reset Information/System OptionsExecutive mode front panel lockout Input you wish to adjustCentering Remote Control of the System 7SC Enabling and disabling executive modeSCP control pads Selecting an input IR 701 infrared remote controlFour Switcher-initiated messages Host-to-switcher communicationsError responses RS-232 Programmer’s GuideUsing the command/response tables Symbol definitionsAscii to Hex conversion table Command Ascii Command Response Additional description Detail mode Video configurationColor TintHorizontal size Image sizeVertical size Top blankingExecutive mode front panel lockout Zap reset to default settingsFirmware version, part number & information requests Delay times Command Ascii Command Response ValuesScaler settings Room relaysAudio settings IR-related settingsMiscellaneous settings Send/receive data to/from page 0 memory Command Hex. command Response Additional descriptionSend/receive data to/from page 1 memory Send/receive a flag parameter blockUsing the control program Installing the softwareMini Mode Control Software for WindowsUser Mode Special featuresConfiguration Real Time Adjustments Projector Driver Room & Misc. Options Saving and restoring configurationsUsing the help program Downloading and using projector driversKey to file names File name Description AAppendix a System 7SC Reference Material SpecificationsSync Reference Material, cont’d Accessories Part Numbers and AccessoriesIncluded parts Replacement Part number Accessories Part numberAlign Notches Firmware Upgrade InstallationSystem 7SC Reference Material Glossary Asia Japan FCC Class a Notice Extron’s WarrantyExtron Electronics, USA