Extron electronic 4LQXI, 4LDXI Audio Level Configuration Menu, Host Baudrate Menu, RGB Delay Menu

Page 31

Chapter 3 • Using the System 4xi Front Panel

When a change is selected, but not yet saved, the selection blinks.

Press to save the selection to memory.

Repeat the above for other input channel numbers.

Press , to go back to the Default Menu.

_______ If the change is made for the input that is currently selected, the projector won't

display the change until the next time the input number is selected.

*4LDxi shown here

**Only NTSC (15.75 kHz) RGB signals can be line-doubled or line-quadrupled

2.Audio Level Configuration Menu

Use

to get to this menu, and then press to select it.

There are two cursor points in the Audio Configuration menu, indicated by the character ">". Use to step between the two positions.

With the cursor in the left position, use or to select a audio input channel.

Only available channel numbers will display.

With the cursor at the right position, use or to set the audio gain/attenuation level for the selected input channel. The range is from -31dB to +31dB.

When a change is selected, but not yet saved, the dB value blinks.

When an audio input is selected, it is connected to the output (except when muted). This menu allows each audio input to be set to match the others.

Press to save the selection to memory.

Press or any input button at any time to exit.

3. Host Baudrate Menu

Use to get to this menu, and then press to select it.

Only the baudrate can be changed; the protocol remains the same.

Use or to select the baudrate for the host system on the RS-232 port.

The choices are listed in the illustration.

The default baudrate is 9600.

The fixed protocol is 8-bits, 1 stop bit, no parity.

When a change is selected, but not yet saved, the value blinks.

Press to save the selection to memory.

Press to go to Menu #0 and then to go back to the Default Menu.

4. RGB Delay Menu

Press

to get to this menu, and then press to select it.

Use this menu to set the time delay for switching the RGB on after the sync has switched. Use or to select the number of seconds (0 to 5 in half-second increments).

When a change is selected, but not yet saved, the value blinks.

Press to save the selection to memory.

Press to go to Menu #0 and then to go back to the Default Menu.

_______ If audio is being switched with the video, the audio will also be delayed.

Press , to go back to the Default Menu.

Extron • System 4xi Switcher Series • User’s Manual

3-8

Image 31
Contents System 4xiEQSeries100 Precautions Getting Started Extron System 4xi Switcher Series User’s Manual Contents Chapter Four Connecting Multiple Switchers Iii Extron System 4xi Switcher Series User’s Manual One Rgbs NTSC/PAL Introduction to SystemSystem 4xi Features Universal Projector Control Multiple Switcher ApplicationsInternal Power Supply with Automatic Switching Picture Control MemorySpecifications Control projector Audio outputGeneral Configuration and Installation System 4xi Rear Panel Identification Rear Panel Connectors and IndicatorsNEC Projector/Monitor ApplicationsCommunications Adapters and Cables Removing the System 4xi CoverUser-Supplied Cables Removing the System 4xi Cover Setting the Main Controller Board for the ProjectorCabling a System 4xi in a Rack Audio Terminal Connections Audio Wiring ApplicationsAudio Cable Equivalent Connections Three Using System 4xi Model Differences Default LCD ScreenTerms used in LCD Menus Menu Controls and NavigationScreen Example of Using the Menu ControlsChoices made for this VGA mode is only Menu Select/Exit Menu Video Mode ConfigurationRGB Delay Menu Audio Level Configuration MenuHost Baudrate Menu LD Sync Configuration Menu Slave Configuration MenuSync Configuration Menu Picture Controls line doubler/line quadrupler converter Slave Switcher Input SelectionInformation Menu Tint Control Horizontal Shift ControlContrast Control Color ControlSystem 4xiSeries LCD Menus Toggle Executive Mode System ResetSpecial Functions 4Chapter Four SW8+ SW10+ Multiple SW8+/SW10+ Looping the System 4xi with Other SwitchersInput Channel Addressing Channel Sys4J1 Pins System 4 J2 Pins Host J3 Pins Slave Switcher Controlling Master/Slave SwitchersSystem 4xi with SW4/6 Armx Switchers System 10 Plus System 4xi with One System 8/10 Plus SwitcherAudio System 4xi with Multiple System 8/10 Plus Switchers System 8/10 Plus Front Access Panel Switches System 8/10 Plus Switch SettingsTesting the Master/Slave Communications Programming the System 4xi Looping Configuration5Chapter Five Connect the PC to the System Extron System Switcher Control SoftwareSystem 4xi Help Example of the first Help menu, Help ContentsWindows Control Panel Examples Window Pull-Down Menus Executive ModeHelp Menu Selections include AAppendix a Program Instruction Levels Programming the System 4xi Series SwitchersRS-232 Connections RS-232 ProtocolThis message will vary depending on the System 4xi model System 4xi -Initiated MessagesRelated Terms Simple Instruction SetCharacter Cmd/Rsp Dec Hex Function Simple Instruction ListAscii Simple Instruction ExamplesHex Switcher Response Error Codes DescriptionExamples Aud/Vid Dsp/Sw Selecting Inputs Using DelimitersHex Response Result Description Advanced Instruction List Error Codes ERCCommand Hex Description Advanced Instruction SetSelect Input CMD4 34h Hex, Decimal and Binary Examples for Converting Range ValuesERC Request Status CMD5 35hSet Slave Configuration CMD8 38h Change System Settings CMD6 36hConfigure an Input Channel CMD9 39h Request Input Channel Configuration CMD10 3Ah4 Configure System CMD11 3Bh4 ESC, CMD12, EOT Request System Configuration CMD12 3Ch4BAppendix B System 4xi Related Parts List Documentation Projector Communication Extension Cables ConnectorsChanging the Main Fuse Video Adapter CablesEnlever le couvercle du Systè me Les câ bles fournis à l’utillsasteurCâ bler un Systè me 4xi sur un rack Entfernung der System 4xi Abdeckung Verkabelung vom System 4xi innerhalb eines Gestells Figure B-10. System 4xi Main Controller Board Extrons Warranty Extron ELECTRONICS, Europe