Extron electronic 4LDXI, 4LQXI manual Programming the System 4xi Looping Configuration

Page 44

Chapter 4 • Connecting Multiple Switchers

Programming the System 4xi Looping Configuration

After making all the connections for a master/ slave system, turn power on for all the units involved and access Menu 5 (Slave Cfg). Use the or to step to the correct

configuration, and then press to save the setting to memory.

_______ This procedure may be done before connecting

the slave(s) to the System 4xi, if that is more convenient.

Testing the Master/Slave Communications

Press to go back to the menu selection again. Step to the Switch Slave menu (Menu 9 if System 4LDxi/4LQxi – otherwise Menu 8). This menu will only appear if there is a slave configured.

Press to get the Switch Slave Menu (shown below). The display will show

Channel 4 because that is the first slave channel.

Use the and to step to a slave channel and press to select it. Once selected, look at the front panel of the slave unit to see that the correct channel has been selected. Using the table on page 4-1, select channel #6 and channel #3 will light on the slave switcher. Repeat this procedure for each available slave channel. (Only the available channels will show in the LCD display.)

Now test the switcher communications in reverse by pressing a channel switch on the slave and see that its system channel number appears in the LCD display. Again, use the table on page 4-1 as a reference.

Once the master/slave system is checked out, all of the available channels can be accessed and set up from the System 4xi front panel with Menus 1 and 2. The channel numbers will be as listed in the left column of the table on page 4-1.

_________ Resetting the system (described on page 3-7) will remove all slave channels

from memory. If that happens, Menu 5 must be used to reconfigure the system.

4-7

Extron • System 4xi Switcher Series • User’s Manual

Image 44
Contents System 4xiEQSeries100 Precautions Getting Started Extron System 4xi Switcher Series User’s Manual Contents Chapter Four Connecting Multiple Switchers Iii Extron System 4xi Switcher Series User’s Manual One Introduction to System Rgbs NTSC/PALSystem 4xi Features Multiple Switcher Applications Internal Power Supply with Automatic SwitchingPicture Control Memory Universal Projector ControlSpecifications General Audio outputControl projector Configuration and Installation Rear Panel Connectors and Indicators System 4xi Rear Panel IdentificationProjector/Monitor Applications NECUser-Supplied Cables Removing the System 4xi CoverCommunications Adapters and Cables Setting the Main Controller Board for the Projector Removing the System 4xi CoverCabling a System 4xi in a Rack Audio Wiring Applications Audio Terminal ConnectionsAudio Cable Equivalent Connections Three Using Default LCD Screen System 4xi Model DifferencesMenu Controls and Navigation Terms used in LCD MenusExample of Using the Menu Controls ScreenChoices made for this VGA mode is only Video Mode Configuration Menu Select/Exit MenuHost Baudrate Menu Audio Level Configuration MenuRGB Delay Menu Sync Configuration Menu Slave Configuration MenuLD Sync Configuration Menu Information Menu Slave Switcher Input SelectionPicture Controls line doubler/line quadrupler converter Horizontal Shift Control Contrast ControlColor Control Tint ControlSystem 4xiSeries LCD Menus Special Functions System ResetToggle Executive Mode 4Chapter Four Looping the System 4xi with Other Switchers Input Channel AddressingChannel Sys4 SW8+ SW10+ Multiple SW8+/SW10+Controlling Master/Slave Switchers J1 Pins System 4 J2 Pins Host J3 Pins Slave SwitcherSystem 4xi with SW4/6 Armx Switchers Audio System 4xi with One System 8/10 Plus SwitcherSystem 10 Plus System 4xi with Multiple System 8/10 Plus Switchers System 8/10 Plus Switch Settings System 8/10 Plus Front Access Panel SwitchesProgramming the System 4xi Looping Configuration Testing the Master/Slave Communications5Chapter Five Extron System Switcher Control Software Connect the PC to the SystemExample of the first Help menu, Help Contents System 4xi HelpWindows Control Panel Examples Executive Mode Window Pull-Down MenusHelp Menu Selections include AAppendix a Programming the System 4xi Series Switchers RS-232 ConnectionsRS-232 Protocol Program Instruction LevelsSystem 4xi -Initiated Messages This message will vary depending on the System 4xi modelSimple Instruction Set Related TermsSimple Instruction List Character Cmd/Rsp Dec Hex FunctionSimple Instruction Examples AsciiError Codes Description Hex Switcher ResponseHex Response Result Description Selecting Inputs Using DelimitersExamples Aud/Vid Dsp/Sw Error Codes ERC Command Hex DescriptionAdvanced Instruction Set Advanced Instruction ListHex, Decimal and Binary Examples for Converting Range Values Select Input CMD4 34hRequest Status CMD5 35h ERCChange System Settings CMD6 36h Set Slave Configuration CMD8 38hConfigure an Input Channel CMD9 39h Request Input Channel Configuration CMD10 3Ah4 Configure System CMD11 3Bh4 Request System Configuration CMD12 3Ch4 ESC, CMD12, EOTBAppendix B System 4xi Related Parts List Projector Communication Extension Cables Connectors Changing the Main FuseVideo Adapter Cables DocumentationLes câ bles fournis à l’utillsasteur Enlever le couvercle du Systè meCâ bler un Systè me 4xi sur un rack Entfernung der System 4xi Abdeckung Verkabelung vom System 4xi innerhalb eines Gestells Figure B-10. System 4xi Main Controller Board Extrons Warranty Extron ELECTRONICS, Europe