Extron electronic Cable Cubby 600 Packaging for Shipment, Figure B-1 Cable Cubby return kit

Page 28

Packaging for Shipment

The Cable Cubby’s ultra-fine machined surfaces and moving parts make them vulnerable to damage caused by mishandling during shipment if they are improperly packaged. If, for any reason, you need to return a Cable Cubby to Extron, first contact Extron to obtain a return kit. The return kit, which reduces the chances of damage during shipment, includes a sturdy shipping carton and foam that can be fitted to each Cable Cubby model (figure B-1).

Figure B-1 — Cable Cubby return kit

Package a Cable Cubby for shipment as follows:

1. Contact the Extron S3 Sales & Technical Support Hotline to obtain a return kit. Extron will send the return kit to the location you specify.

WThe flanged edges of the top of the surface enclosure are sharp when the Cable Cubby is removed from the table. Exercise caution when handling to prevent personal injury.

CThe flanged edges of the top of the surface enclosure are bevelled to an ultra-fine thickness of less than

0.04(4/100)” (approximately 1 mm). These edges are soft and can be easily nicked or bent. Exercise caution when handling and mounting the enclosure. Mishandling can damage the appearance of the enclosure.

2. Disconnect and retain all cables, remove and retain the AAP shelf assembly(s) (CC 300, 600, 800) and remove the Cable Cubby from the table or desk. See Removing and Replacing the Cubby, steps 1 through 4, in chapter 3, Maintenance and Modifications.

NFor Cable Cubby 300, 600, and 800 models, retain the screw clamps.

3.

Install the plastic strips that protect the flanged edges of

 

the top of the surface enclosure (figure B-2).

Figure B-2 — Installing protective strips

NFor Cable Cubby 200 models proceed to step 13.

For Cable Cubby 300, 600, and 800 models, continue to step 4, below.

4. Remove and retain the top foam pad from the carton.

5. CC 300, 600, 800 only — Remove and discard the center foam section of the cushion in the carton (figure B-3). If you are returning a Cable Cubby 300 model, this is the correct fit. Proceed to step 8.

B-2

Cable Cubby® Products • Packaging for Shipment

Cable Cubby® Products • Packaging for Shipment

B-3

Image 28
Contents Cable Cubby Page Table of Contents Introduction Table of Contents, cont’dCable Cubby Products Introduction About the Cable Cubby ProductsFeatures Introduction, cont’dInstallation TwoInstallation Overview InstallationPreparing the Routing Template Installation, cont’d Preparing the Table Preparing the table with a routerInstallation, cont’d Installing the Cables and AAPsPreparing the table with a hole saw Cable Cubby 300C only AAP shelf brackets CC 300, 600Installing the cables Installing the power module CC 300, 600Installing the AAPs Adjusting the cable position CC Installing the shelf assembly CC 300, 600Mounting the Cable Cubby Cable Cubby 300C Maintenance and Modifications Maintenance and Modifications Removing and Replacing the Cable CubbyMaintenance and Modifications, cont’d Replacing Cables or an AAPInternational Cable Cubby 600 with second power module Cable Cubby 600 with second power module Installing the power module Reference InformationSpecifications Reference InformationGeneral Packaging for Shipment, cont’d Cable CubbyCable Cubby Part Numbers Cable Cubby Part numberReplacement/Modification Part Numbers Packaging for Shipment, cont’d Included PartsTop Plate Dimensions Routing Template Part NumbersCable Cubby Cable Cubby 300C Packaging for Shipment Cable CubbyPackaging for Shipment Figure B-1 Cable Cubby return kitFigure B-3 Removing center foam Figure B-7 Placing the cubby in the carton Packaging for Shipment, cont’d Packaging for Shipment Precautions Extron’s Warranty