Extron electronic Cable Cubby 200 user manual Installation, cont’d, Installing the Cables and AAPs

Page 10

Installation, cont’d

Preparing the table with a hole saw (Cable Cubby 300C only)

Prepare the table with a hole saw as follows:

1. On the tabletop or other installation surface, mark the 6" circle, then find and mark the center of the circle.

WWear safety glasses when operating the drill. Failure to comply can result in eye injury.

2.

Using a portable drill with a 6" (or 152 mm) hole saw,

 

carefully cut the opening in the table surface at the

 

desired location (figure 2-3). Extron is not responsible for

 

improperly positioned Cable Cubbies.

CUse a portable drill with sufficient power to handle the 6” hole saw. Exercise caution when handling the drill and hole saw. Take care to protect the mounting surface from damage.

Figure 2-3 — Cutting the opening with a hole saw

Installing the Cables and AAPs

Each Cable Cubby 300, 600, and 800 model ships with one or two moveable AAP shelf assemblies. The Cable Cubby 200’s AAP shelf is fixed in place.

AAP shelf brackets (CC 300, 600, 800)

Each shipped AAP shelf assembly consists of a set of shelf brackets and a number of cable pass-through (split) AAPs. Depending on the Cable Cubby model, each set of shelf brackets supports either two, three, or four single-space AAPs (figure 2-4).

Four-Space Shelf Bracket

Three-Space Shelf Bracket

Two-Space Shelf Bracket

and Split AAPs

and Split AAPs

and Split AAPs

Figure 2-4 — Shelf brackets

The simplest way to install the cables and AAPs in the Cable Cubby 300, 600, and 800 is to populate the shelf brackets with split and/or standard AAPs outside the cubby and then install the populated AAP shelf assembly into the cubby.

NCable cubby 300, 600, and 800 only —

On US/domestic models, the power module takes up two AAP spaces. On IEC, EU, Swiss, UK, Israeli, and Australian models, the power module takes up three AAP spaces. Cable pass-through AAPs take two, three, or four AAP spaces. Consider the arrangement of the Cable Cubby AAPs when you install them so that you do not waste AAP space.

2-6

Cable Cubby® Products • Installation

Cable Cubby® Products • Installation

2-7

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Cable Cubby Page Table of Contents Introduction Table of Contents, cont’dCable Cubby Products Introduction About the Cable Cubby ProductsFeatures Introduction, cont’dInstallation TwoInstallation Overview InstallationPreparing the Routing Template Installation, cont’d Preparing the Table Preparing the table with a routerPreparing the table with a hole saw Cable Cubby 300C only Installation, cont’dInstalling the Cables and AAPs AAP shelf brackets CC 300, 600Installing the cables Installing the power module CC 300, 600Installing the AAPs Adjusting the cable position CC Installing the shelf assembly CC 300, 600Mounting the Cable Cubby Cable Cubby 300C Maintenance and Modifications Maintenance and Modifications Removing and Replacing the Cable CubbyMaintenance and Modifications, cont’d Replacing Cables or an AAPInternational Cable Cubby 600 with second power module Cable Cubby 600 with second power module Installing the power module Reference InformationSpecifications Reference InformationGeneral Packaging for Shipment, cont’d Cable CubbyCable Cubby Part Numbers Cable Cubby Part numberReplacement/Modification Part Numbers Packaging for Shipment, cont’d Included PartsTop Plate Dimensions Routing Template Part NumbersCable Cubby Cable Cubby 300C Packaging for Shipment Cable CubbyPackaging for Shipment Figure B-1 Cable Cubby return kitFigure B-3 Removing center foam Figure B-7 Placing the cubby in the carton Packaging for Shipment, cont’d Packaging for Shipment Precautions Extron’s Warranty
Top Page Image Contents