Extron electronic Cable Cubby 600 user manual Routing Template Part Numbers, Top Plate Dimensions

Page 24

Packaging for Shipment, cont’d

AAP shelf brackets (CC 300, 600, 800)

Part number

 

 

Four-space AAP Cable Cubby bracket (set of 2) (figure A-2)

70-273-01

Three-space AAP Cable Cubby bracket (set of 2) (figure A-2)

70-272-01

Two-space AAP Cable Cubby bracket (set of 2) (figure A-2)

70-271-01

Single-space AAP Cable Cubby bracket (set of 2) (figure A-2)

70-392-01

Four-Space Shelf Bracket

Three-Space Shelf Bracket

Two-Space Shelf Bracket

and Split AAPs

and Split AAPs

and Split AAPs

Figure A-2 — Shelf brackets

Grommet and plug kit

Part number

NThe kit listed below includes three grommets; one large, one medium, and one small.

Grommet and hole plug kit

70-387-01

Routing Template Part Numbers

The following reuseable sheet metal routing templates are recommended for installation and are available at no charge.

Template

Part number

 

 

Cable Cubby 200 routing template

70-384-01

Cable Cubby 300S/300C routing template

70-237-01

Cable Cubby 600 routing template

70-239-01

Cable Cubby 800 routing template

70-240-01

Top Plate Dimensions

There are two preferred and recommended methods for cutting the table: either use the appropriate metal routing template (figure A-3 and chapter 2, Installation) and a router or use a hole saw (Cable Cubby 300C only). The templates (see Routing Template Part Numbers, for part numbers) are available at no cost.

CABLE CUBBY 300

USER ACCESS

HSA 200

USER ACCESS

HSA 200

CABLE CUBBY 300

Figure A-3 — CC 300S/300C metal routing template

If you choose not to use Extron’s metal routing templates, the cut-out templates (figure A-4, figure A-5, figure A-6, figure A-7, and figure A-8) will help you properly prepare the mounting surface. The cutout templates are not to scale and are for reference only. The surface cut-out area dimensions for the template are marked in bold type.

For full size paper templates, visit the Extron Web site (http://www.extron.com) or call the Extron S3 Sales & Technical Support Hotline.

A-10 Cable Cubby® Products • Packaging for Shipment

Cable Cubby® Products • Packaging for Shipment A-11

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Cable Cubby Page Table of Contents Table of Contents, cont’d IntroductionCable Cubby Products Introduction About the Cable Cubby ProductsFeatures Introduction, cont’dInstallation TwoInstallation Installation OverviewPreparing the Routing Template Installation, cont’d Preparing the Table Preparing the table with a routerInstallation, cont’d Installing the Cables and AAPsPreparing the table with a hole saw Cable Cubby 300C only AAP shelf brackets CC 300, 600Installing the power module CC 300, 600 Installing the cablesInstalling the AAPs Installing the shelf assembly CC 300, 600 Adjusting the cable position CCMounting the Cable Cubby Cable Cubby 300C Maintenance and Modifications Maintenance and Modifications Removing and Replacing the Cable CubbyMaintenance and Modifications, cont’d Replacing Cables or an AAPInternational Cable Cubby 600 with second power module Cable Cubby 600 with second power module Installing the power module Reference InformationReference Information SpecificationsGeneral Packaging for Shipment, cont’d Cable CubbyCable Cubby Part Numbers Cable Cubby Part numberReplacement/Modification Part Numbers Packaging for Shipment, cont’d Included PartsTop Plate Dimensions Routing Template Part NumbersCable Cubby Cable Cubby 300C Packaging for Shipment Cable CubbyPackaging for Shipment Figure B-1 Cable Cubby return kitFigure B-3 Removing center foam Figure B-7 Placing the cubby in the carton Packaging for Shipment, cont’d Packaging for Shipment Precautions Extron’s Warranty
Top Page Image Contents