Extron electronic IPL T PC1i manual Resetting, Front Panel Security Lockout Executive Mode

Page 18

Front Panel Security Lockout (Executive Mode)

When the PC1 is in front panel lock mode (executive mode), it does not accept commands from the front panel. If any button is pressed while the unit is in executive mode, the Power LED flashes three times, indicating that the input from the front panel is not being accepted.

To enter or exit executive mode, press and hold the receptacle Power button for 3 seconds. The Power LED flashes three times to indicate that the executive mode has been switched.

NOTES: • If power to the PC1 is recycled while the unit is in executive mode, the PC1 remains in executive mode.

• The Reset button is always functional. It is recessed to avoid it being pressed accidentally.

Resetting

Reset the unit by pressing the Reset button on the front panel. This button is recessed, and can be accessed with an Extron Tweeker or other small Phillips screwdriver.

CAUTIONS: • Review the reset modes carefully. Use of the wrong reset mode may cause unintended loss of flash memory programming or a unit reboot.

•The reset modes described on the following pages break all TCP/IP connections by closing all sockets to the unit.

IPLT PC1

R

POWER

I

TX

 

 

RX

INPUT

 

 

100

 

IR

 

 

LINK

 

 

ACT

Recessed Reset Button Use tip of Philips head on Tweeker to activate.

Figure 9. Reset Button

NOTES: • If the Reset button is continually held in, the Power LED pulses (blinks) every

3 seconds, and with each pulse, the PC1 goes into a different reset mode. For

mode 5, the LED blinks three times, indicating that it is the last mode.

• The reset modes are separate functions, not a progression from mode 1 to mode 5.

IPL T PC1 • Front Panel Features and Operation 12

Page 17 Page 19
Image 18
Page 17 Page 19
Contents IPL T PC1 IPL T PC1iVorsicht AvertissementAchtung PrecaucionFCC Class a Notice Software Commands Conventions Used in this GuideNotifications Contents IPL T PC1 Contents About this Guide FeaturesIntroduction About the IPL T PC1IPL T PC1 Introduction Application Diagram Extron IPL T PC1iInstallation Rear Panel Installation OverviewThis section describes Rear Panels IPL T PC1 Rear Panel 120 VACConnecting Cables Accessing the Communication SheetRS-232 Port Cabling Connecting the Display Device To connect the display device to the PC1Wiring the Local Area Network LAN Port Wiring for IR ControlRJ-45 Connector Wiring Wiring the Contact Input Port Front Panel Features Operation Front Panel FeaturesSetting Up the System Using the Front Panel Setting Up Power Control of the Output DeviceResetting Front Panel Security Lockout Executive ModeResult ModeActivation Purpose and notesHold the Reset button in until the Power LED blinks twice Hold the Reset button in until the Power LED blinks oncePurpose and notes This mode is used for troubleshooting Four times in quick succession, confirming a mode 4 resetConfiguration Control Configuring the Hardware for Ethernet ControlSetting Up and Configuring the PC1 Using ARP Space must separate arp and the hyphenSetting Up and Configuring the PC1 Using a Web Browser IPL T PC1 LAN port defaultsSetting Up the Computer for IP Communication Network Connections WindowEnter the following values as shown below Default gatewayOn the Local Area Connection Properties window, select IP addressConfiguring the IPL T PC1 Using a Web Browser Internet Protocol TCP/IP Properties Window for Windows XPSystem Settings Page with Default IP Address Using the IPL T PC1 Web Pages Password Prompt WindowViewing the System Status System Status ScreenUsing the Configuration Pages Specifying system settingsIP settings Date and time settingsConfiguring the RS-232 Port and the AC Receptacle Contact input portUsing the IR Drivers RS-232 portAC receptacle Performing a command Assigning passwordsRemoving passwords Click SubmitEntering e-mail addresses Mail Alerts Page Upper PortionSetting up Smtp authentication Upgrading Firmware Downloading the firmware from the webUpdating the firmware Click Browse to open a Choose file window Firmware File Selected on the Choose File WindowScheduling ScheduleScheduling output receptacle power To schedule power on and off to the output receptacleScheduling front panel lockout executive mode Set Schedule For Field for Executive ModeScheduling by day of the week Changing an individual setting Managing FilesUploading files to the web Adding a directory Other file management functionsServer Side Includes SSIs Where x is the SIS command to be executedCustom Web Pages Query stringsCode example Web Page Html Source Code Document Showing SSIsSpecial characters Reserved characters URL encodingReserved characters Character Hexadecimal DecimalAccessing and Using Telnet Port Unsafe charactersConnecting to the IP Address Troubleshooting Power ConnectionsNetwork Connections Global Configurator Software Response to an Unsuccessful Ping CommandMessages Initiated by the IPL T PC1 SIS Programming ControlHost-to-Interface Communication IPL T PC1 IP addressPassword Information Error ResponsesError Response References Using the Command and Response Table Telnet Web BrowserPort and must be hex encoded if non-alphanumeric Symbol Definitions X2% = priority set to Send Data String command parametersX2# X3#X4$ X3%X4@ X4%X7# X6$X7@ X7$Command and Response Table for SIS Commands Example Mail Server Setup Commands Mail CommandsWeb Browser-specific Commands IP Setup CommandsSet GMT offset24 # CZ Password and Security Settings Remapping Port DesignationsTelnet text responses File CommandsVar file new Array Web responses Html sample codeFile memory See belowTelnet text responses Send a page GET on port 80 followed by WSFReset Zap and Erase Commands DefaultSpecifications Reference MaterialIR control interface GeneralPart Numbers and Accessories Mounting the IPL T PC1 InterfaceRack mounting procedure Under-desk MountingMounting the IPL T PC1 Under Furniture Mbps or 100 Mbps GlossaryNumbers and a Device’s MAC or physical machine addressOn and off by the PC1 Addresses in an organization’s networkControls devices 10 Mbps or 100 MbpsTwo ports HyperText objects from remote web pagesIts corresponding physical MAC address on the LAN Standard ports used are 23 for Telnet and 80 for EthernetLocated, and accessed Are used in these commands and responsesPoint at which a device starts to operate at standby power Or networks on the InternetConfiguration or provide you with feedback GlobalViewer, and your custom web pagesAsia Middle East USA, Canada, South America Japan Central AmericaEurope, Africa, and the Middle China East Europe
Related manuals
Manual 2 pages 39.09 Kb Manual 27 pages 50.4 Kb

IPL T PC1, IPL T PC1i specifications

The Extron Electronics IPL T PC1 i and IPL T PC1 are advanced presentation and control processors designed for optimal efficiency in various audiovisual applications. These devices serve as integral components in many professional environments, offering sophisticated capabilities for managing and automating AV systems.

Both models feature a robust, intuitive user interface that simplifies the management of complex audiovisual setups. The IPL T PC1 i and IPL T PC1 enable seamless integration with a variety of control systems, enhancing the user experience and providing streamlined operation. With their scalable design, these devices can cater to the needs of small conference rooms to large auditoriums, making them versatile solutions for diverse applications.

One standout feature of the IPL T PC1 i is its support for Extron's GUI Designer software. This powerful tool allows users to create customized graphical user interfaces tailored to specific AV systems, ensuring that control remains user-friendly and accessible. The IPL T PC1 i also supports a wide range of communication protocols, including Ethernet, RS-232, and USB, which facilitates compatibility with multiple devices and technologies.

Both models are equipped with advanced signal processing capabilities. They offer support for high-resolution video formats, ensuring that presentations and multimedia displays maintain their quality. Options for signal routing and switching further enhance the functionality of the devices, allowing for dynamic and adaptive presentations.

The IPL T PC1 i and IPL T PC1 also feature built-in scheduling and automation capabilities. Users can program specific tasks, such as turning systems on or off, adjusting volume levels, and changing input sources, at predetermined times. This feature maximizes efficiency, minimizes the need for manual intervention, and ensures that AV systems are ready when needed.

In terms of physical design, both models are compact and rack-mountable, allowing for easy installation in equipment racks or dedicated AV cabinets. They also include comprehensive diagnostic tools for troubleshooting and system monitoring, ensuring optimal performance and reliability.

Overall, the Extron Electronics IPL T PC1 i and IPL T PC1 stand out as reliable, feature-rich solutions for managing AV systems in a variety of settings, making them a popular choice among AV professionals and institutions alike. Their blend of adaptability, user interface design, and robust signal processing capabilities positions them as leaders in the AV control market.
Top Page Image Contents