Extron electronic IPL T PC1i manual Upgrading Firmware, Downloading the firmware from the web

Page 38

Upgrading Firmware

The Firmware Upgrade page lets you browse to locate and upload a new version of firmware for your unit. The uploaded file must have the file extension .S19.

NOTE: The PC1 uses the same firmware as the IPL T PC1. However, it does not accept

other firmware files, such as the .s19 files for the IP Link S Series.

To find out the version of firmware that is currently loaded on your PC1, see “Firmware:” in the System Description section of the System Status page.

Downloading the firmware from the web

To obtain the firmware file to load to your PC1:

1.Visit the Extron website (www.extron.com).

2.Click the Download tab.

3.On the Download Center page, click the Firmware link at the top of the left sidebar menu.

4.On the Archives line at the top of the Firmware page, click the letter I.

5.On the next page that appears, click the Download link at the right end of the IPL T PC1 or IPL T PC1i line.

6.Fill in the required information on the next Download Center page, and click the

Download IPLTPC1 button.

7.Click Run on the File Download window.

8.Follow the instructions on the installation wizard screens. The new firmware file is placed on your computer internal disk.

Updating the firmware

To upload a new version of firmware:

1.On the sidebar menu of the Configuration page, click Firmware Upgrade. The Firmware

Upgrade page is displayed, showing the version of firmware that is currently loaded.

Figure 24. Firmware Upgrade Page

IPL T PC1 • HTML Configuration and Control 32

Page 37 Page 39
Image 38
Page 37 Page 39
Contents IPL T PC1 IPL T PC1iVorsicht AvertissementAchtung PrecaucionFCC Class a Notice Notifications Software CommandsConventions Used in this Guide Contents IPL T PC1 Contents About this Guide FeaturesIntroduction About the IPL T PC1IPL T PC1 Introduction Application Diagram Extron IPL T PC1iThis section describes Installation Rear PanelInstallation Overview Rear Panels IPL T PC1 Rear Panel 120 VACRS-232 Port Cabling Connecting CablesAccessing the Communication Sheet Connecting the Display Device To connect the display device to the PC1RJ-45 Connector Wiring Wiring the Local Area Network LAN PortWiring for IR Control Wiring the Contact Input Port Front Panel Features Operation Front Panel FeaturesSetting Up the System Using the Front Panel Setting Up Power Control of the Output DeviceResetting Front Panel Security Lockout Executive ModeResult ModeActivation Purpose and notesHold the Reset button in until the Power LED blinks twice Hold the Reset button in until the Power LED blinks oncePurpose and notes This mode is used for troubleshooting Four times in quick succession, confirming a mode 4 resetConfiguration Control Configuring the Hardware for Ethernet ControlSetting Up and Configuring the PC1 Using ARP Space must separate arp and the hyphenSetting Up and Configuring the PC1 Using a Web Browser IPL T PC1 LAN port defaultsSetting Up the Computer for IP Communication Network Connections WindowEnter the following values as shown below Default gatewayOn the Local Area Connection Properties window, select IP addressConfiguring the IPL T PC1 Using a Web Browser Internet Protocol TCP/IP Properties Window for Windows XPSystem Settings Page with Default IP Address Using the IPL T PC1 Web Pages Password Prompt WindowViewing the System Status System Status ScreenUsing the Configuration Pages Specifying system settingsIP settings Date and time settingsConfiguring the RS-232 Port and the AC Receptacle Contact input portAC receptacle Using the IR DriversRS-232 port Performing a command Assigning passwordsRemoving passwords Click SubmitEntering e-mail addresses Mail Alerts Page Upper PortionSetting up Smtp authentication Updating the firmware Upgrading FirmwareDownloading the firmware from the web Click Browse to open a Choose file window Firmware File Selected on the Choose File WindowScheduling ScheduleScheduling output receptacle power To schedule power on and off to the output receptacleScheduling front panel lockout executive mode Set Schedule For Field for Executive ModeScheduling by day of the week Uploading files to the web Changing an individual settingManaging Files Adding a directory Other file management functionsServer Side Includes SSIs Where x is the SIS command to be executedCustom Web Pages Query stringsCode example Web Page Html Source Code Document Showing SSIsSpecial characters Reserved characters URL encodingReserved characters Character Hexadecimal DecimalAccessing and Using Telnet Port Unsafe charactersConnecting to the IP Address Network Connections TroubleshootingPower Connections Global Configurator Software Response to an Unsuccessful Ping CommandMessages Initiated by the IPL T PC1 SIS Programming ControlHost-to-Interface Communication IPL T PC1 IP addressError Response References Password InformationError Responses Port and must be hex encoded if non-alphanumeric Using the Command and Response TableTelnet Web Browser Symbol Definitions X2% = priority set to Send Data String command parametersX2# X3#X4$ X3%X4@ X4%X7# X6$X7@ X7$Command and Response Table for SIS Commands Example Mail Server Setup Commands Mail CommandsWeb Browser-specific Commands IP Setup CommandsSet GMT offset24 # CZ Password and Security Settings Remapping Port DesignationsTelnet text responses File CommandsVar file new Array Web responses Html sample codeFile memory See belowTelnet text responses Send a page GET on port 80 followed by WSFReset Zap and Erase Commands DefaultSpecifications Reference MaterialIR control interface GeneralPart Numbers and Accessories Mounting the IPL T PC1 InterfaceRack mounting procedure Under-desk MountingMounting the IPL T PC1 Under Furniture Mbps or 100 Mbps GlossaryNumbers and a Device’s MAC or physical machine addressOn and off by the PC1 Addresses in an organization’s networkControls devices 10 Mbps or 100 MbpsTwo ports HyperText objects from remote web pagesIts corresponding physical MAC address on the LAN Standard ports used are 23 for Telnet and 80 for EthernetLocated, and accessed Are used in these commands and responsesPoint at which a device starts to operate at standby power Or networks on the InternetConfiguration or provide you with feedback GlobalViewer, and your custom web pagesAsia Middle East USA, Canada, South America Japan Central AmericaEurope, Africa, and the Middle China East Europe
Related manuals
Manual 2 pages 39.09 Kb Manual 27 pages 50.4 Kb

IPL T PC1, IPL T PC1i specifications

The Extron Electronics IPL T PC1 i and IPL T PC1 are advanced presentation and control processors designed for optimal efficiency in various audiovisual applications. These devices serve as integral components in many professional environments, offering sophisticated capabilities for managing and automating AV systems.

Both models feature a robust, intuitive user interface that simplifies the management of complex audiovisual setups. The IPL T PC1 i and IPL T PC1 enable seamless integration with a variety of control systems, enhancing the user experience and providing streamlined operation. With their scalable design, these devices can cater to the needs of small conference rooms to large auditoriums, making them versatile solutions for diverse applications.

One standout feature of the IPL T PC1 i is its support for Extron's GUI Designer software. This powerful tool allows users to create customized graphical user interfaces tailored to specific AV systems, ensuring that control remains user-friendly and accessible. The IPL T PC1 i also supports a wide range of communication protocols, including Ethernet, RS-232, and USB, which facilitates compatibility with multiple devices and technologies.

Both models are equipped with advanced signal processing capabilities. They offer support for high-resolution video formats, ensuring that presentations and multimedia displays maintain their quality. Options for signal routing and switching further enhance the functionality of the devices, allowing for dynamic and adaptive presentations.

The IPL T PC1 i and IPL T PC1 also feature built-in scheduling and automation capabilities. Users can program specific tasks, such as turning systems on or off, adjusting volume levels, and changing input sources, at predetermined times. This feature maximizes efficiency, minimizes the need for manual intervention, and ensures that AV systems are ready when needed.

In terms of physical design, both models are compact and rack-mountable, allowing for easy installation in equipment racks or dedicated AV cabinets. They also include comprehensive diagnostic tools for troubleshooting and system monitoring, ensuring optimal performance and reliability.

Overall, the Extron Electronics IPL T PC1 i and IPL T PC1 stand out as reliable, feature-rich solutions for managing AV systems in a variety of settings, making them a popular choice among AV professionals and institutions alike. Their blend of adaptability, user interface design, and robust signal processing capabilities positions them as leaders in the AV control market.
Top Page Image Contents