Extron electronic IPL T PC1i manual Part Numbers and Accessories, Mounting the IPL T PC1 Interface

Page 70

Part Numbers and Accessories

Included Parts

These items are included in each order for an IPL T PC1 or IPL T PC1i interface:

Included Parts

Part Number

IPL T PC1

60-544-10

IPL T PC1i

60-544-20

 

 

Rubber feet (self-adhesive) (4)

 

 

 

2-pin female captive screw terminal (2)

 

4-pin female captive screw terminal (1)

 

 

 

18 AWG IEC power cord (U. S. shipments only)

 

 

 

Tweeker (small screwdriver)

 

IPL T PC1 Setup Guide

 

 

 

IPL T PC1 Software CD-ROM

 

Optional Accessories

These items are optional for the IPL T PC1 and the IPL T PCli:

Optional Accessories

Part Number

 

 

RSU 129 Universal Rack Shelf Kit (9.5 inches deep)

60-190-01

 

 

 

RSB 129

Basic Rack Shelf (9.5 inches deep)

60-604-02

 

 

 

RSU 126

Universal Rack Shelf Kit (6 inches deep)

60-190-10

RSB 126

Basic Rack Shelf (6 inches deep)

60-604-11

 

 

MBU 125 1/2 Rack Width Low-Profile Mount Kit

70-077-01

Mounting the IPL T PC1 Interface

The IPL T PC1 can be set on a table, mounted on a rack shelf, or mounted under furniture such as a desk, podium, or tabletop.

Tabletop Use

Four self-adhesive rubber feet are included with the PC1. For tabletop use, attach one foot at each corner of the bottom side of the unit, and place the PC1 in the desired location.

Rack Mounting

Rack mount the interface, if desired, using one of the optional 19 inches wide rack shelves (see “Optional Accessories,” above, for part numbers).

UL requirements for rack mounting

The following Underwriters Laboratories (UL) requirements pertain to the installation of the interface into a rack.

•Elevated operating ambient temperature — If the equipment is installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient temperature. Therefore, consider installing the equipment in an environment compatible with the maximum ambient temperature (TMA) specified by the manufacturer.

IPL T PC1 • SIS Programming and Control 64

Page 69 Page 71
Image 70
Page 69 Page 71
Contents IPL T PC1 IPL T PC1iVorsicht AvertissementAchtung PrecaucionFCC Class a Notice Conventions Used in this Guide Software CommandsNotifications Contents IPL T PC1 Contents About this Guide FeaturesIntroduction About the IPL T PC1IPL T PC1 Introduction Application Diagram Extron IPL T PC1iInstallation Overview Installation Rear PanelThis section describes Rear Panels IPL T PC1 Rear Panel 120 VACAccessing the Communication Sheet Connecting CablesRS-232 Port Cabling Connecting the Display Device To connect the display device to the PC1Wiring for IR Control Wiring the Local Area Network LAN PortRJ-45 Connector Wiring Wiring the Contact Input Port Front Panel Features Operation Front Panel FeaturesSetting Up the System Using the Front Panel Setting Up Power Control of the Output DeviceResetting Front Panel Security Lockout Executive ModeResult ModeActivation Purpose and notesHold the Reset button in until the Power LED blinks twice Hold the Reset button in until the Power LED blinks oncePurpose and notes This mode is used for troubleshooting Four times in quick succession, confirming a mode 4 resetConfiguration Control Configuring the Hardware for Ethernet ControlSetting Up and Configuring the PC1 Using ARP Space must separate arp and the hyphenSetting Up and Configuring the PC1 Using a Web Browser IPL T PC1 LAN port defaultsSetting Up the Computer for IP Communication Network Connections WindowEnter the following values as shown below Default gatewayOn the Local Area Connection Properties window, select IP addressConfiguring the IPL T PC1 Using a Web Browser Internet Protocol TCP/IP Properties Window for Windows XPSystem Settings Page with Default IP Address Using the IPL T PC1 Web Pages Password Prompt WindowViewing the System Status System Status ScreenUsing the Configuration Pages Specifying system settingsIP settings Date and time settingsConfiguring the RS-232 Port and the AC Receptacle Contact input portRS-232 port Using the IR DriversAC receptacle Performing a command Assigning passwordsRemoving passwords Click SubmitEntering e-mail addresses Mail Alerts Page Upper PortionSetting up Smtp authentication Downloading the firmware from the web Upgrading FirmwareUpdating the firmware Click Browse to open a Choose file window Firmware File Selected on the Choose File WindowScheduling ScheduleScheduling output receptacle power To schedule power on and off to the output receptacleScheduling front panel lockout executive mode Set Schedule For Field for Executive ModeScheduling by day of the week Managing Files Changing an individual settingUploading files to the web Adding a directory Other file management functionsServer Side Includes SSIs Where x is the SIS command to be executedCustom Web Pages Query stringsCode example Web Page Html Source Code Document Showing SSIsSpecial characters Reserved characters URL encodingReserved characters Character Hexadecimal DecimalAccessing and Using Telnet Port Unsafe charactersConnecting to the IP Address Power Connections TroubleshootingNetwork Connections Global Configurator Software Response to an Unsuccessful Ping CommandMessages Initiated by the IPL T PC1 SIS Programming ControlHost-to-Interface Communication IPL T PC1 IP addressError Responses Password InformationError Response References Telnet Web Browser Using the Command and Response TablePort and must be hex encoded if non-alphanumeric Symbol Definitions X2% = priority set to Send Data String command parametersX2# X3#X4$ X3%X4@ X4%X7# X6$X7@ X7$Command and Response Table for SIS Commands Example Mail Server Setup Commands Mail CommandsWeb Browser-specific Commands IP Setup CommandsSet GMT offset24 # CZ Password and Security Settings Remapping Port DesignationsTelnet text responses File CommandsVar file new Array Web responses Html sample codeFile memory See belowTelnet text responses Send a page GET on port 80 followed by WSFReset Zap and Erase Commands DefaultSpecifications Reference MaterialIR control interface GeneralPart Numbers and Accessories Mounting the IPL T PC1 InterfaceRack mounting procedure Under-desk MountingMounting the IPL T PC1 Under Furniture Mbps or 100 Mbps GlossaryNumbers and a Device’s MAC or physical machine addressOn and off by the PC1 Addresses in an organization’s networkControls devices 10 Mbps or 100 MbpsTwo ports HyperText objects from remote web pagesIts corresponding physical MAC address on the LAN Standard ports used are 23 for Telnet and 80 for EthernetLocated, and accessed Are used in these commands and responsesPoint at which a device starts to operate at standby power Or networks on the InternetConfiguration or provide you with feedback GlobalViewer, and your custom web pagesAsia Middle East USA, Canada, South America Japan Central AmericaEurope, Africa, and the Middle China East Europe
Related manuals
Manual 2 pages 39.09 Kb Manual 27 pages 50.4 Kb

IPL T PC1, IPL T PC1i specifications

The Extron Electronics IPL T PC1 i and IPL T PC1 are advanced presentation and control processors designed for optimal efficiency in various audiovisual applications. These devices serve as integral components in many professional environments, offering sophisticated capabilities for managing and automating AV systems.

Both models feature a robust, intuitive user interface that simplifies the management of complex audiovisual setups. The IPL T PC1 i and IPL T PC1 enable seamless integration with a variety of control systems, enhancing the user experience and providing streamlined operation. With their scalable design, these devices can cater to the needs of small conference rooms to large auditoriums, making them versatile solutions for diverse applications.

One standout feature of the IPL T PC1 i is its support for Extron's GUI Designer software. This powerful tool allows users to create customized graphical user interfaces tailored to specific AV systems, ensuring that control remains user-friendly and accessible. The IPL T PC1 i also supports a wide range of communication protocols, including Ethernet, RS-232, and USB, which facilitates compatibility with multiple devices and technologies.

Both models are equipped with advanced signal processing capabilities. They offer support for high-resolution video formats, ensuring that presentations and multimedia displays maintain their quality. Options for signal routing and switching further enhance the functionality of the devices, allowing for dynamic and adaptive presentations.

The IPL T PC1 i and IPL T PC1 also feature built-in scheduling and automation capabilities. Users can program specific tasks, such as turning systems on or off, adjusting volume levels, and changing input sources, at predetermined times. This feature maximizes efficiency, minimizes the need for manual intervention, and ensures that AV systems are ready when needed.

In terms of physical design, both models are compact and rack-mountable, allowing for easy installation in equipment racks or dedicated AV cabinets. They also include comprehensive diagnostic tools for troubleshooting and system monitoring, ensuring optimal performance and reliability.

Overall, the Extron Electronics IPL T PC1 i and IPL T PC1 stand out as reliable, feature-rich solutions for managing AV systems in a variety of settings, making them a popular choice among AV professionals and institutions alike. Their blend of adaptability, user interface design, and robust signal processing capabilities positions them as leaders in the AV control market.
Top Page Image Contents