Gigabyte GS-R12T4H2-RH manual Super I/O

Page 10

GS-R12T4H2-RH Rack Mount Server

 

 

(Support RAID 0, 1, 1E) (Option)

 

 

 

Super I/O

 

 

Controller

ITE IT8720F Super I/O

 

 

 

Front I/O

2 X USB 2.0 connector

Rear I/O

2 x P/S 2 ports

 

1 x Serial port

 

4 x USB 2.0 ports

 

1 x VGA connector

 

2 x RJ45 LAN ports

 

1 x 10/100 LAN port (for server management)

 

 

 

System BIOS:

 

 

BIOS Type

Phoenix BIOS on 16Mb flash ROM

 

Server Management Functions: (Optional device)

BMC Chip

Server Engine PilotII IPMI 2.0 controller

Failure Detection

IPMI 2.0 specification of Server management

Event Logging

64KB Nonvolatile Memory to Log System Failure Events

Remote Management

Follow the IPMI 2.0 specification of Server management

 

 

 

Environment

 

 

AmbientTemperature

Operating Temperature: 5oC to 35oC

 

Non-operating Temperature: 0oC to 50oC

Relative Humidity

10-80% operating Humidity at 30o C

 

 

 

System Dimention:

430Wx43.5Hx710D (mm)

Electrical Power Supply

Fixed 1U PSU 600W at 80% efficiency

1 0

Image 10
Contents Service Guide Preface Table of Contents Power Security Server  Important safety information  Precaution for Product with Laser Devices Federal Communications Commission FCC Statement  FCC part 68 applicable to products fitted with USA modems Canadian Department of Communications Compliance Statement Class a equipment System Specification Super I/O System Hardware Installation Remove the chassis cover Installing the Processor Installing the Heat Sink Installing the Memeory Module 1716 1 5 7 6Code Dimm Population Table Channel a Channel B Channel CQuad-Rank Single-Rank Dual-Rank Installing the PCI Expansion Card GS-R12T4H2-RH Rack Mount Server Installing the Hard Disk Drive HDD Security Lock Installing and Replacing the FAN Duct Replacing the FAN Assemblly Replacing the Motherboard Replacing the Power Supply GS-R12T4H2-RH Rack Mount Server Replacing the Chassis Cover Appearance of GS-R12T4H2-RH Front View of GS-R12T4H2-RHRear View of GS-R12T4H2-RH Front Panel LED Indicator Indicator Color State DescriptionLAN1 LAN port LED Indicator  Description SAS/SATA HDD indicator Green Red Hard Disk Drive LED DescriptionGC-BS14U-RH Back plane board Components Code DescriptionSystem Block Diagram Intel ICH10RConnector Icon Description Suggest Icon DescriptionMotherboard Placement and Jumper Setting GA-7TTSE-RH Motherboard ComponentItem Component BIOSRVCR1 Bios Revocery jumper Jumper SettingCLRCMOS1 Clear Cmos jumper JPSTRAP2/ JPSTRAP8 PilotII firmware upgrade jumper Meenable BMC Selection jumperPASSDIS1 Skip Supervisor password jumper CLRRTC1 Clear RTC jumperExpansion Card Components Description Bios Setup  Boot Status Page Setup Menu / Option Page Setup Menu Power MainMenuSystem Time BIOSInformantionSystem Date Processor InformationTotalMemory Advanced Processor Configuration Execute Disable Bit Processor ConfigurationMultiprocessor Specification Intel R Virtualization TechnologySetMaxExtCPUID=3 Machine CheckingFast String Operations EchoTPREist GV3 & C State Processor Power ManagementEISTPSDFunction CPU C State TurboModeState Osacpi C3 ReportPackage C State Limit CPU C7 ReportAcpi Mwait extensions Memory Configuration Change Interleave setting Memory Control SettingsMemory RAS Mode Rank Interleave settingAdvanced Chipset Configuration 1 Intel VT for Directed I/O VT-d Coherency Support Intel VT forDirected I/O VT-dInterruptRemapping PassThrough DMAQPI Error Report QPI Control SettingsQPI Link Fast Mode MemoryECCErrorLogOnboard LAN1 Control PCI ConfigurationOnboard LAN iSCSI Boot ROM LAN1OptionROMLAN2OptionROM Legacy USB SupportSata Configuration Sata ConfigurationSerial ATA Sata Port 0/1/2/3/4/5Multi-Sector Transfer Serial Port a DeviceConfigurationSerial Port B GS-R12T4H2-RH Rack Mount Server Boot -time Diagnostic Screen Boot DeviceConfigurationPost Error Pause NumLock Thermal and Acoustic Configuration Temperature guardband Temperature hysteresisClose loop Thermal Throttle Power After Power FailureSet Supervisor Password SecuritySet User Password Password on bootServer System Management System Management BMC IPAddress SourceFlowControl Console RedirectionConsole Redirection Baud RateTerminal Type Continue C.R. after PostBoot Exit Saving Changes Exit Discarding ChangesDiscard Changes Load SettupDefaultSave Changes