Gigabyte GS-R12T4H2-RH manual Installing the Hard Disk Drive

Page 21

GS-R12T4H2-RH Rack Mount Server

Installing the Hard Disk Drive

Step 1 Press the release button.

Step 2 Pull the locking lever to remove the HDD tray. Step 3 Slide hard disk into blank.

Step 4 Secure the hard drive to the tray with four (4) screws as shown. Do not over tighten the screws. Slide the blank into the bay until it locks into place.

Step 5 Engage the HDD Security Lock. For detail instruction, please see the following section. Step 6 Connect cable and power.

1

3

2

4

4

2 1

Image 21

Contents Service Guide Preface Table of Contents Power Security Server  Precaution for Product with Laser Devices  Important safety information FCC part 68 applicable to products fitted with USA modems  Federal Communications Commission FCC Statement Canadian Department of Communications Compliance Statement Class a equipment System Specification Super I/O System Hardware Installation Remove the chassis cover Installing the Processor Installing the Heat Sink Installing the Memeory Module 7 6 1716 1 5Code Channel a Channel B Channel C Dimm Population TableQuad-Rank Single-Rank Dual-Rank Installing the PCI Expansion Card GS-R12T4H2-RH Rack Mount Server Installing the Hard Disk Drive HDD Security Lock Installing and Replacing the FAN Duct Replacing the FAN Assemblly Replacing the Motherboard Replacing the Power Supply GS-R12T4H2-RH Rack Mount Server Replacing the Chassis Cover Front View of GS-R12T4H2-RH Appearance of GS-R12T4H2-RHRear View of GS-R12T4H2-RH Indicator Color State Description Front Panel LED IndicatorLAN1   LAN port LED IndicatorHard Disk Drive LED Description Description SAS/SATA HDD indicator Green RedCode Description GC-BS14U-RH Back plane board ComponentsIntel ICH10R System Block DiagramSuggest Icon Description Connector Icon DescriptionGA-7TTSE-RH Motherboard Component Motherboard Placement and Jumper SettingItem Component Jumper Setting BIOSRVCR1 Bios Revocery jumperCLRCMOS1 Clear Cmos jumper PASSDIS1 Skip Supervisor password jumper Meenable BMC Selection jumperJPSTRAP2/ JPSTRAP8 PilotII firmware upgrade jumper CLRRTC1 Clear RTC jumperExpansion Card Components Description Bios Setup  Power Status Page Setup Menu / Option Page Setup Menu Boot MainMenuSystem Date BIOSInformantionSystem Time Processor InformationTotalMemory Advanced Processor Configuration Multiprocessor Specification Processor ConfigurationExecute Disable Bit Intel R Virtualization TechnologyFast String Operations Machine CheckingSetMaxExtCPUID=3 EchoTPRProcessor Power Management Eist GV3 & C StateEISTPSDFunction State TurboModeCPU C State Osacpi C3 ReportCPU C7 Report Package C State LimitAcpi Mwait extensions Memory Configuration Memory RAS Mode Memory Control SettingsChange Interleave setting Rank Interleave settingAdvanced Chipset Configuration 1 Intel VT for Directed I/O VT-d InterruptRemapping Intel VT forDirected I/O VT-dCoherency Support PassThrough DMAQPI Link Fast Mode QPI Control SettingsQPI Error Report MemoryECCErrorLogOnboard LAN iSCSI Boot ROM PCI ConfigurationOnboard LAN1 Control LAN1OptionROMLegacy USB Support LAN2OptionROMSata Configuration Sata ConfigurationSata Port 0/1/2/3/4/5 Serial ATAMulti-Sector Transfer DeviceConfiguration Serial Port aSerial Port B GS-R12T4H2-RH Rack Mount Server Boot DeviceConfiguration Boot -time Diagnostic ScreenPost Error Pause NumLock Thermal and Acoustic Configuration Temperature hysteresis Temperature guardbandClose loop Thermal Throttle After Power Failure PowerSecurity Set Supervisor PasswordPassword on boot Set User PasswordServer System Management BMC IPAddress Source System ManagementConsole Redirection Console RedirectionFlowControl Baud RateContinue C.R. after Post Terminal TypeBoot Exit Discarding Changes Exit Saving ChangesLoad SettupDefault Discard ChangesSave Changes