Gigabyte GS-R12T4H2-RH manual Console Redirection, FlowControl, Baud Rate

Page 77

Use Serial Port A as the COM port address. Use Serial Port B as the COM port address. Disable this function. (Default setting)

GS-R12T4H2-RH Rack Mount Server

Console Redirection

Figure 5-2: Console Redirection

Console Redirection

If this option is set to enabled, it will use a port on the motherboard to run console redirection function.

On-board COM A

On-board COM B Disabled

FlowControl

This option provide user to enable the flow control function.

None	Not supported.
XON/XOFF	Software control.
CTS/RTS	Hardware control. (Default setting)

Baud Rate

7 7

Image 77

Contents Service Guide Preface Table of Contents Power Security Server  Precaution for Product with Laser Devices  Important safety information FCC part 68 applicable to products fitted with USA modems  Federal Communications Commission FCC Statement Canadian Department of Communications Compliance Statement Class a equipment System Specification Super I/O System Hardware Installation Remove the chassis cover Installing the Processor Installing the Heat Sink Installing the Memeory Module Code 7 61716 1 5 Channel a Channel B Channel C Dimm Population TableQuad-Rank Single-Rank Dual-Rank Installing the PCI Expansion Card GS-R12T4H2-RH Rack Mount Server Installing the Hard Disk Drive HDD Security Lock Installing and Replacing the FAN Duct Replacing the FAN Assemblly Replacing the Motherboard Replacing the Power Supply GS-R12T4H2-RH Rack Mount Server Replacing the Chassis Cover Front View of GS-R12T4H2-RH Appearance of GS-R12T4H2-RHRear View of GS-R12T4H2-RH Indicator Color State Description Front Panel LED IndicatorLAN1   LAN port LED IndicatorHard Disk Drive LED Description Description SAS/SATA HDD indicator Green RedCode Description GC-BS14U-RH Back plane board ComponentsIntel ICH10R System Block DiagramSuggest Icon Description Connector Icon DescriptionGA-7TTSE-RH Motherboard Component Motherboard Placement and Jumper SettingItem Component CLRCMOS1 Clear Cmos jumper Jumper SettingBIOSRVCR1 Bios Revocery jumper PASSDIS1 Skip Supervisor password jumper Meenable BMC Selection jumperJPSTRAP2/ JPSTRAP8 PilotII firmware upgrade jumper CLRRTC1 Clear RTC jumperExpansion Card Components Description Bios Setup  Power Status Page Setup Menu / Option Page Setup Menu Boot MainMenuSystem Date BIOSInformantionSystem Time Processor InformationTotalMemory Advanced Processor Configuration Multiprocessor Specification Processor ConfigurationExecute Disable Bit Intel R Virtualization TechnologyFast String Operations Machine CheckingSetMaxExtCPUID=3 EchoTPREISTPSDFunction Processor Power ManagementEist GV3 & C State State TurboModeCPU C State Osacpi C3 ReportAcpi Mwait extensions CPU C7 ReportPackage C State Limit Memory Configuration Memory RAS Mode Memory Control SettingsChange Interleave setting Rank Interleave settingAdvanced Chipset Configuration 1 Intel VT for Directed I/O VT-d InterruptRemapping Intel VT forDirected I/O VT-dCoherency Support PassThrough DMAQPI Link Fast Mode QPI Control SettingsQPI Error Report MemoryECCErrorLogOnboard LAN iSCSI Boot ROM PCI ConfigurationOnboard LAN1 Control LAN1OptionROMLegacy USB Support LAN2OptionROMSata Configuration Sata ConfigurationSata Port 0/1/2/3/4/5 Serial ATAMulti-Sector Transfer Serial Port B DeviceConfigurationSerial Port a GS-R12T4H2-RH Rack Mount Server Post Error Pause Boot DeviceConfigurationBoot -time Diagnostic Screen NumLock Thermal and Acoustic Configuration Close loop Thermal Throttle Temperature hysteresisTemperature guardband After Power Failure PowerSecurity Set Supervisor PasswordPassword on boot Set User PasswordServer System Management BMC IPAddress Source System ManagementConsole Redirection Console RedirectionFlowControl Baud RateContinue C.R. after Post Terminal TypeBoot Exit Discarding Changes Exit Saving ChangesSave Changes Load SettupDefaultDiscard Changes