Gigabyte GS-R12T4H2-RH manual  Federal Communications Commission FCC Statement

Page 6

Safety Information

*To reduce the risk of fire, use only No. 26 AWG or larger telecommunications line cord.

*Do not plug a modem or telephone cable into the network interface controller (NIC) receptacle.

*Disconnect the modem cable before opening a product enclosure, touching or installing internal components, or touching an uninsulated modem cable or jack.

*Do not use a telephone line to report a gas leak while you are in the vicinity of the leak.

Federal Communications Commission (FCC) Statement

Warning

This is a class A product. In a domestic environment this product may cause radio interference

In which case the user may be required to take adequate measures.

Note: This equipment has been tested and found to comply with the limits for a ClassA digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Neither the provider nor the manufacturer are responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)this device may not cause harmful interference, and

(2)this device must accept any interference received, including interference that may cause undesired operation.

FCC part 68 (applicable to products fitted with USA modems)

The modem complies with Part 68 of the FCC Rules. On this equipment is a label that contains, among other information, the FCC registration number and Ringer Equivalence Number (REN) for this equipment. You must, upon request, provide this information to your telephone company.

If your telephone equipment causes harm to the telephone network, the Telephone Company may discontinue your service temporarily. If possible, they will notify in advance. But, if advance notice is not practical, you will be notified as soon as possible. You will be informed of your right to file a complaint with

6

Image 6
Contents Service Guide Preface Table of Contents Power Security Server  Important safety information  Precaution for Product with Laser Devices Federal Communications Commission FCC Statement  FCC part 68 applicable to products fitted with USA modems Canadian Department of Communications Compliance Statement Class a equipment System Specification Super I/O System Hardware Installation Remove the chassis cover Installing the Processor Installing the Heat Sink Installing the Memeory Module 7 6 1716 1 5Code Dimm Population Table Channel a Channel B Channel CQuad-Rank Single-Rank Dual-Rank Installing the PCI Expansion Card GS-R12T4H2-RH Rack Mount Server Installing the Hard Disk Drive HDD Security Lock Installing and Replacing the FAN Duct Replacing the FAN Assemblly Replacing the Motherboard Replacing the Power Supply GS-R12T4H2-RH Rack Mount Server Replacing the Chassis Cover Appearance of GS-R12T4H2-RH Front View of GS-R12T4H2-RHRear View of GS-R12T4H2-RH Front Panel LED Indicator Indicator Color State DescriptionLAN1 LAN port LED Indicator  Description SAS/SATA HDD indicator Green Red Hard Disk Drive LED DescriptionGC-BS14U-RH Back plane board Components Code DescriptionSystem Block Diagram Intel ICH10RConnector Icon Description Suggest Icon DescriptionMotherboard Placement and Jumper Setting GA-7TTSE-RH Motherboard ComponentItem Component Jumper Setting BIOSRVCR1 Bios Revocery jumperCLRCMOS1 Clear Cmos jumper JPSTRAP2/ JPSTRAP8 PilotII firmware upgrade jumper Meenable BMC Selection jumperPASSDIS1 Skip Supervisor password jumper CLRRTC1 Clear RTC jumperExpansion Card Components Description Bios Setup  Boot Status Page Setup Menu / Option Page Setup Menu Power MainMenuSystem Time BIOSInformantionSystem Date Processor InformationTotalMemory Advanced Processor Configuration Execute Disable Bit Processor ConfigurationMultiprocessor Specification Intel R Virtualization TechnologySetMaxExtCPUID=3 Machine CheckingFast String Operations EchoTPRProcessor Power Management Eist GV3 & C StateEISTPSDFunction CPU C State TurboModeState Osacpi C3 ReportCPU C7 Report Package C State LimitAcpi Mwait extensions Memory Configuration Change Interleave setting Memory Control SettingsMemory RAS Mode Rank Interleave settingAdvanced Chipset Configuration 1 Intel VT for Directed I/O VT-d Coherency Support Intel VT forDirected I/O VT-dInterruptRemapping PassThrough DMAQPI Error Report QPI Control SettingsQPI Link Fast Mode MemoryECCErrorLogOnboard LAN1 Control PCI ConfigurationOnboard LAN iSCSI Boot ROM LAN1OptionROMLAN2OptionROM Legacy USB SupportSata Configuration Sata ConfigurationSerial ATA Sata Port 0/1/2/3/4/5Multi-Sector Transfer DeviceConfiguration Serial Port aSerial Port B GS-R12T4H2-RH Rack Mount Server Boot DeviceConfiguration Boot -time Diagnostic ScreenPost Error Pause NumLock Thermal and Acoustic Configuration Temperature hysteresis Temperature guardbandClose loop Thermal Throttle Power After Power FailureSet Supervisor Password SecuritySet User Password Password on bootServer System Management System Management BMC IPAddress SourceFlowControl Console RedirectionConsole Redirection Baud RateTerminal Type Continue C.R. after PostBoot Exit Saving Changes Exit Discarding ChangesLoad SettupDefault Discard ChangesSave Changes