Gigabyte GS-R12T4H2-RH manual Processor Power Management, Eist GV3 & C State, EISTPSDFunction

Page 51

GS-R12T4H2-RH Rack Mount Server

Processor Power Management

	Figure 2-1-1: Processor Power Management
EIST (GV3) & C State
Enabled	Enable EIST (GV3) and C State items. (Default setting)
Disabled	Disable EIST (GV3) and C State items.
EIST(GV3)
Enabled	Enable EIST (GV3. (Default setting)
Disabled	Disable EIST (GV3).
EISTPSDFunction
HW_ALL	In HW_ALL mode, the rpocessor hardware is responsible for coordinating
	the P-state among logical processors dependencies. The OS is responsible
	for keeping the P-state request up to date on all logical processors.
	(Default setting)

5 1

Image 51

Contents Service Guide Preface Table of Contents Power Security Server  Precaution for Product with Laser Devices  Important safety information FCC part 68 applicable to products fitted with USA modems  Federal Communications Commission FCC Statement Canadian Department of Communications Compliance Statement Class a equipment System Specification Super I/O System Hardware Installation Remove the chassis cover Installing the Processor Installing the Heat Sink Installing the Memeory Module 7 6 1716 1 5Code Channel a Channel B Channel C Dimm Population TableQuad-Rank Single-Rank Dual-Rank Installing the PCI Expansion Card GS-R12T4H2-RH Rack Mount Server Installing the Hard Disk Drive HDD Security Lock Installing and Replacing the FAN Duct Replacing the FAN Assemblly Replacing the Motherboard Replacing the Power Supply GS-R12T4H2-RH Rack Mount Server Replacing the Chassis Cover Front View of GS-R12T4H2-RH Appearance of GS-R12T4H2-RHRear View of GS-R12T4H2-RH Indicator Color State Description Front Panel LED IndicatorLAN1   LAN port LED IndicatorHard Disk Drive LED Description Description SAS/SATA HDD indicator Green RedCode Description GC-BS14U-RH Back plane board ComponentsIntel ICH10R System Block DiagramSuggest Icon Description Connector Icon DescriptionGA-7TTSE-RH Motherboard Component Motherboard Placement and Jumper SettingItem Component Jumper Setting BIOSRVCR1 Bios Revocery jumperCLRCMOS1 Clear Cmos jumper CLRRTC1 Clear RTC jumper Meenable BMC Selection jumperPASSDIS1 Skip Supervisor password jumper JPSTRAP2/ JPSTRAP8 PilotII firmware upgrade jumperExpansion Card Components Description Bios Setup MainMenu Status Page Setup Menu / Option Page Setup Menu Power  BootProcessor Information BIOSInformantionSystem Date System TimeTotalMemory Advanced Processor Configuration Intel R Virtualization Technology Processor ConfigurationMultiprocessor Specification Execute Disable BitEchoTPR Machine CheckingFast String Operations SetMaxExtCPUID=3Processor Power Management Eist GV3 & C StateEISTPSDFunction Osacpi C3 Report TurboModeState CPU C StateCPU C7 Report Package C State LimitAcpi Mwait extensions Memory Configuration Rank Interleave setting Memory Control SettingsMemory RAS Mode Change Interleave settingAdvanced Chipset Configuration 1 Intel VT for Directed I/O VT-d PassThrough DMA Intel VT forDirected I/O VT-dInterruptRemapping Coherency SupportMemoryECCErrorLog QPI Control SettingsQPI Link Fast Mode QPI Error ReportLAN1OptionROM PCI ConfigurationOnboard LAN iSCSI Boot ROM Onboard LAN1 ControlLegacy USB Support LAN2OptionROMSata Configuration Sata ConfigurationSata Port 0/1/2/3/4/5 Serial ATAMulti-Sector Transfer DeviceConfiguration Serial Port aSerial Port B GS-R12T4H2-RH Rack Mount Server Boot DeviceConfiguration Boot -time Diagnostic ScreenPost Error Pause NumLock Thermal and Acoustic Configuration Temperature hysteresis Temperature guardbandClose loop Thermal Throttle After Power Failure PowerSecurity Set Supervisor PasswordPassword on boot Set User PasswordServer System Management BMC IPAddress Source System ManagementBaud Rate Console RedirectionConsole Redirection FlowControlContinue C.R. after Post Terminal TypeBoot Exit Discarding Changes Exit Saving ChangesLoad SettupDefault Discard ChangesSave Changes