Gigabyte GS-R12T4H2-RH manual Terminal Type, Continue C.R. after Post

Page 78

BIOS Setup

This option allows user to set the specified baud rate.

Options

300, 1200, 2400, 9600, 19.2K, 38.4K, 57.6K, 115.2K.

Terminal Type

This option allows user to select the specified terminal type. This is defined by IEEE.

OptionsVT100, VT100 8bit, PC-ANSI 7bit, PC-ANSI, VT100+, VT-UTF8,

ASCII.

Continue C.R. after POST

This option allows user to enable console redirection after O.S has loaded.

On	Enable console redirection after O.S has loaded.
Off	Disable this function. (Default setting)

7 8

Image 78

Contents Service Guide Preface Table of Contents Power Security Server  Important safety information  Precaution for Product with Laser Devices Federal Communications Commission FCC Statement  FCC part 68 applicable to products fitted with USA modems Canadian Department of Communications Compliance Statement Class a equipment System Specification Super I/O System Hardware Installation Remove the chassis cover Installing the Processor Installing the Heat Sink Installing the Memeory Module 7 6 1716 1 5Code Dimm Population Table Channel a Channel B Channel CQuad-Rank Single-Rank Dual-Rank Installing the PCI Expansion Card GS-R12T4H2-RH Rack Mount Server Installing the Hard Disk Drive HDD Security Lock Installing and Replacing the FAN Duct Replacing the FAN Assemblly Replacing the Motherboard Replacing the Power Supply GS-R12T4H2-RH Rack Mount Server Replacing the Chassis Cover Appearance of GS-R12T4H2-RH Front View of GS-R12T4H2-RHRear View of GS-R12T4H2-RH Front Panel LED Indicator Indicator Color State DescriptionLAN1 LAN port LED Indicator  Description SAS/SATA HDD indicator Green Red Hard Disk Drive LED DescriptionGC-BS14U-RH Back plane board Components Code DescriptionSystem Block Diagram Intel ICH10RConnector Icon Description Suggest Icon DescriptionMotherboard Placement and Jumper Setting GA-7TTSE-RH Motherboard ComponentItem Component Jumper Setting BIOSRVCR1 Bios Revocery jumperCLRCMOS1 Clear Cmos jumper JPSTRAP2/ JPSTRAP8 PilotII firmware upgrade jumper Meenable BMC Selection jumperPASSDIS1 Skip Supervisor password jumper CLRRTC1 Clear RTC jumperExpansion Card Components Description Bios Setup  Boot Status Page Setup Menu / Option Page Setup Menu Power MainMenuSystem Time BIOSInformantionSystem Date Processor InformationTotalMemory Advanced Processor Configuration Execute Disable Bit Processor ConfigurationMultiprocessor Specification Intel R Virtualization TechnologySetMaxExtCPUID=3 Machine CheckingFast String Operations EchoTPRProcessor Power Management Eist GV3 & C StateEISTPSDFunction CPU C State TurboModeState Osacpi C3 ReportCPU C7 Report Package C State LimitAcpi Mwait extensions Memory Configuration Change Interleave setting Memory Control SettingsMemory RAS Mode Rank Interleave settingAdvanced Chipset Configuration 1 Intel VT for Directed I/O VT-d Coherency Support Intel VT forDirected I/O VT-dInterruptRemapping PassThrough DMAQPI Error Report QPI Control SettingsQPI Link Fast Mode MemoryECCErrorLogOnboard LAN1 Control PCI ConfigurationOnboard LAN iSCSI Boot ROM LAN1OptionROMLAN2OptionROM Legacy USB SupportSata Configuration Sata ConfigurationSerial ATA Sata Port 0/1/2/3/4/5Multi-Sector Transfer DeviceConfiguration Serial Port aSerial Port B GS-R12T4H2-RH Rack Mount Server Boot DeviceConfiguration Boot -time Diagnostic ScreenPost Error Pause NumLock Thermal and Acoustic Configuration Temperature hysteresis Temperature guardbandClose loop Thermal Throttle Power After Power FailureSet Supervisor Password SecuritySet User Password Password on bootServer System Management System Management BMC IPAddress SourceFlowControl Console RedirectionConsole Redirection Baud RateTerminal Type Continue C.R. after PostBoot Exit Saving Changes Exit Discarding ChangesLoad SettupDefault Discard ChangesSave Changes