Gigabyte GS-R12T4H2-RH manual Installing the PCI Expansion Card

Page 19

Hardware Installation Process

Installing the PCI Expansion Card

Step 1 Lift the riser bracket slightly, then pull it out from the server chassis. Step 2 Loosen the riser bracket screws.

Step 3 Attach the mini card to the riser bracket and ecure the mini card with screws.

Step 4 Attach the mini card to the riser bracket the other side. Secure the mini card with screws. Step 5 Slide the expansion card into the slot until the card firmly seats.

Step 6 Secure th expansion card with screws. Step 7 Align the riser bracket to the system module.

2

2

1

1 9

Image 19

Contents Service Guide Preface Table of Contents Power Security Server  Precaution for Product with Laser Devices  Important safety information FCC part 68 applicable to products fitted with USA modems  Federal Communications Commission FCC Statement Canadian Department of Communications Compliance Statement Class a equipment System Specification Super I/O System Hardware Installation Remove the chassis cover Installing the Processor Installing the Heat Sink Installing the Memeory Module 1716 1 5 7 6Code Channel a Channel B Channel C Dimm Population TableQuad-Rank Single-Rank Dual-Rank Installing the PCI Expansion Card GS-R12T4H2-RH Rack Mount Server Installing the Hard Disk Drive HDD Security Lock Installing and Replacing the FAN Duct Replacing the FAN Assemblly Replacing the Motherboard Replacing the Power Supply GS-R12T4H2-RH Rack Mount Server Replacing the Chassis Cover Front View of GS-R12T4H2-RH Appearance of GS-R12T4H2-RHRear View of GS-R12T4H2-RH Indicator Color State Description Front Panel LED IndicatorLAN1   LAN port LED IndicatorHard Disk Drive LED Description Description SAS/SATA HDD indicator Green RedCode Description GC-BS14U-RH Back plane board ComponentsIntel ICH10R System Block DiagramSuggest Icon Description Connector Icon DescriptionGA-7TTSE-RH Motherboard Component Motherboard Placement and Jumper SettingItem Component BIOSRVCR1 Bios Revocery jumper Jumper SettingCLRCMOS1 Clear Cmos jumper CLRRTC1 Clear RTC jumper Meenable BMC Selection jumperPASSDIS1 Skip Supervisor password jumper JPSTRAP2/ JPSTRAP8 PilotII firmware upgrade jumperExpansion Card Components Description Bios Setup MainMenu Status Page Setup Menu / Option Page Setup Menu Power  BootProcessor Information BIOSInformantionSystem Date System TimeTotalMemory Advanced Processor Configuration Intel R Virtualization Technology Processor ConfigurationMultiprocessor Specification Execute Disable BitEchoTPR Machine CheckingFast String Operations SetMaxExtCPUID=3Eist GV3 & C State Processor Power ManagementEISTPSDFunction Osacpi C3 Report TurboModeState CPU C StatePackage C State Limit CPU C7 ReportAcpi Mwait extensions Memory Configuration Rank Interleave setting Memory Control SettingsMemory RAS Mode Change Interleave settingAdvanced Chipset Configuration 1 Intel VT for Directed I/O VT-d PassThrough DMA Intel VT forDirected I/O VT-dInterruptRemapping Coherency SupportMemoryECCErrorLog QPI Control SettingsQPI Link Fast Mode QPI Error ReportLAN1OptionROM PCI ConfigurationOnboard LAN iSCSI Boot ROM Onboard LAN1 ControlLegacy USB Support LAN2OptionROMSata Configuration Sata ConfigurationSata Port 0/1/2/3/4/5 Serial ATAMulti-Sector Transfer Serial Port a DeviceConfigurationSerial Port B GS-R12T4H2-RH Rack Mount Server Boot -time Diagnostic Screen Boot DeviceConfigurationPost Error Pause NumLock Thermal and Acoustic Configuration Temperature guardband Temperature hysteresisClose loop Thermal Throttle After Power Failure PowerSecurity Set Supervisor PasswordPassword on boot Set User PasswordServer System Management BMC IPAddress Source System ManagementBaud Rate Console RedirectionConsole Redirection FlowControlContinue C.R. after Post Terminal TypeBoot Exit Discarding Changes Exit Saving ChangesDiscard Changes Load SettupDefaultSave Changes