Gigabyte GS-R12T4H2-RH manual Installing and Replacing the FAN Duct

Page 23

GS-R12T4H2-RH Rack Mount Server

Installing and Replacing the FAN Duct

Step 1 Remove the airducts from the chassis by pulling the rear edge in the direction of the arrow Step 2 With fan duct installation, align the fan duct with the guiding groove. Push down the fan duct

into chassis until its firmly seats.

1

2

2 3

Image 23

Contents Service Guide Preface Table of Contents Power Security Server  Precaution for Product with Laser Devices  Important safety information FCC part 68 applicable to products fitted with USA modems  Federal Communications Commission FCC Statement Canadian Department of Communications Compliance Statement Class a equipment System Specification Super I/O System Hardware Installation Remove the chassis cover Installing the Processor Installing the Heat Sink Installing the Memeory Module Code 7 61716 1 5 Channel a Channel B Channel C Dimm Population TableQuad-Rank Single-Rank Dual-Rank Installing the PCI Expansion Card GS-R12T4H2-RH Rack Mount Server Installing the Hard Disk Drive HDD Security Lock Installing and Replacing the FAN Duct Replacing the FAN Assemblly Replacing the Motherboard Replacing the Power Supply GS-R12T4H2-RH Rack Mount Server Replacing the Chassis Cover Front View of GS-R12T4H2-RH Appearance of GS-R12T4H2-RHRear View of GS-R12T4H2-RH Indicator Color State Description Front Panel LED IndicatorLAN1   LAN port LED IndicatorHard Disk Drive LED Description Description SAS/SATA HDD indicator Green RedCode Description GC-BS14U-RH Back plane board ComponentsIntel ICH10R System Block DiagramSuggest Icon Description Connector Icon DescriptionGA-7TTSE-RH Motherboard Component Motherboard Placement and Jumper SettingItem Component CLRCMOS1 Clear Cmos jumper Jumper SettingBIOSRVCR1 Bios Revocery jumper CLRRTC1 Clear RTC jumper Meenable BMC Selection jumperPASSDIS1 Skip Supervisor password jumper JPSTRAP2/ JPSTRAP8 PilotII firmware upgrade jumperExpansion Card Components Description Bios Setup MainMenu Status Page Setup Menu / Option Page Setup Menu Power  BootProcessor Information BIOSInformantionSystem Date System TimeTotalMemory Advanced Processor Configuration Intel R Virtualization Technology Processor ConfigurationMultiprocessor Specification Execute Disable BitEchoTPR Machine CheckingFast String Operations SetMaxExtCPUID=3EISTPSDFunction Processor Power ManagementEist GV3 & C State Osacpi C3 Report TurboModeState CPU C StateAcpi Mwait extensions CPU C7 ReportPackage C State Limit Memory Configuration Rank Interleave setting Memory Control SettingsMemory RAS Mode Change Interleave settingAdvanced Chipset Configuration 1 Intel VT for Directed I/O VT-d PassThrough DMA Intel VT forDirected I/O VT-dInterruptRemapping Coherency SupportMemoryECCErrorLog QPI Control SettingsQPI Link Fast Mode QPI Error ReportLAN1OptionROM PCI ConfigurationOnboard LAN iSCSI Boot ROM Onboard LAN1 ControlLegacy USB Support LAN2OptionROMSata Configuration Sata ConfigurationSata Port 0/1/2/3/4/5 Serial ATAMulti-Sector Transfer Serial Port B DeviceConfigurationSerial Port a GS-R12T4H2-RH Rack Mount Server Post Error Pause Boot DeviceConfigurationBoot -time Diagnostic Screen NumLock Thermal and Acoustic Configuration Close loop Thermal Throttle Temperature hysteresisTemperature guardband After Power Failure PowerSecurity Set Supervisor PasswordPassword on boot Set User PasswordServer System Management BMC IPAddress Source System ManagementBaud Rate Console RedirectionConsole Redirection FlowControlContinue C.R. after Post Terminal TypeBoot Exit Discarding Changes Exit Saving ChangesSave Changes Load SettupDefaultDiscard Changes