Pelco FX82052 manual Replace local module, Indication Fefi On local module Optical signal, Partner

Page 28

Table C. Troubleshooting with Front-Panel Indicators (Continued)

Indicator Color

Meaning

Possible Cause

 

Corrective Action

 

 

 

 

 

 

 

100BASE-FX Status LED (

 

)

 

 

 

 

 

 

 

 

 

 

Green

A fiber link is

 

No action required.

 

established.

 

 

 

 

 

 

 

 

 

 

Flashing green

Data activity is

 

No action required.

 

occurring on the fiber

 

 

 

 

 

link; data is being

 

 

 

 

 

transmitted or

 

 

 

 

 

received.

 

 

 

 

 

 

 

 

 

Red

Far end fault

Defective fiber transmit port

Replace local module.

 

indication (FEFI).

on local module

 

 

 

The optical signal

 

 

 

 

 

Laser fault on local module

Refer to the Optic Fault LED

 

transmitted from this

 

(Optic Fault LED on local

section in this table.

 

port is not detected

 

module flashes red).

 

 

 

by the remote link

 

 

 

 

 

 

 

 

Defective fiber receive port

Replace remote module.

 

partner.

 

on remote module

 

 

 

 

 

 

 

 

 

 

 

 

NOTE: The Optic Fault LED on the remote module is red. Refer to the Optic Fault

 

LED section in this table for additional information.

 

 

 

 

 

 

 

 

 

 

 

 

(Continued on next page)

28

C2607M (2/07)

Image 28
Contents Ethernet Switch Contents List of IllustrationsTX Mode Switch Settings FX Mode Switch Settings List of TablesImportant Safety Instructions Risk of Electric Shock Do not Open Regulatory Notices Radio and Television InterferenceProduct Overview DescriptionPOINT-TO-POINT Application with Fiber Redundancy C2607M 2/07 Models FX82052, -2 Models Multimode ModelsSingle-Mode Models† FX82052, -4 Models Multimode ModelsFront Panel Power LED Pelco badge100BASE-FX Status LED Per fiber port a and B 10BASE-T/100BASE-TX Ports 1-5,RJ-45 connectors Rear Panel10BASE-T/100BASE-TX Ports 1-5 RJ-45 connectors FX82052 Rear PANEL, -4 ModelsInstallation Package ContentsAutonegotiation is enabled by default Flow control is disabled by defaultSetting Fiber Failover Mode Table A. TX Mode Switch SettingsFlow control default setting 10BASE-T/100BASE-TX Modes of OperationTable B. FX Mode Switch Settings Mode of OperationDefault setting Secondary fiber linkMounting Mounting the FX82052 Module Into a RackMounting the FX82052 Module Using the Wall Clip FX82052 Connections, -4 Models SC Fiber Connectors Shown Connections10BASE-T/100BASE-TX connections Fiber connectionsFiber Link FX Mode Position Fiber Ports a and B Are Independent FX Mode Position FX Mode Position Fiber Ports a and B Are Independent Troubleshooting Check power connectionModule Reseat module or power Supply as necessary Replace power supplyMeaning Indication Fefi On local module Optical signal Optic Fault LED on local Section in this tableReplace local module By the remote linkMeaning Possible Cause Corrective Action Optic Fault LED Table D. Troubleshooting with Rear-Panel Indicators Desired, refer to SettingAmber If 10BASE-T operation isMeaning Possible Cause Corrective Action Duplex mode Duplex mode Duplex linkRefer to Setting If half-duplex mode isMode refer to Setting Green Port is set to If 100BASE-TX full-duplexFull-duplex operation is not Flashing green Port is set to Normal or excessiveTable D. Troubleshooting with Rear-Panel Indicators Optic Fault optic signal/laser status per fiber port SpecificationsLink/activity and speed, duplex/collision and speed FX82052, -2 Models Wavelength Optical Maximum Multimode 62.5/125 μmSingle-Mode 9/125 μm FX82052SSTR-2Fibers Appendix. RJ-45 Connector Pinouts Illustrates RJ-45 MDI/MDI-X connector pinoutsProduct Warranty and Return Information ISO9001