Pelco FX82052 manual Fibers

Page 37

FX82052, -4 Models

		Wavelength		Optical	Maximum
		(Transmit/Receive)*		Optical	Maximum
	Number	(Transmit/Receive)*		Power	Transmission
	Number			Power	Transmission
Model Number	of Fibers	Fiber Port A	Fiber Port B	Budget	Distance

		Multimode (62.5/125 μm)

FX82052MSTR-4	4 (2 per port)	1310/1310 nm	1310/1310 nm	26 dB†	6 km (3.7 mi)‡
FX82052MSCR-4	4 (2 per port)	1310/1310 nm	1310/1310 nm	26 dB†	6 km (3.7 mi)‡
		Single-Mode (9/125 μm)

FX82052SSTR-4	4 (2 per port)	1310/1310 nm	1310/1310 nm	28 dB	46 km (28.6 mi)§
FX82052SSCR-4	4 (2 per port)	1310/1310 nm	1310/1310 nm	28 dB	46 km (28.6 mi)§

* The FX82052 module is classified by the FDA as a Class 1 laser product. For 1310 nm, the Class 1 laser limit is <15.6 mW.

† When using 50/125 μm multimode fiber, subtract 3 dB from the optical power budget.

‡ Maximum transmission distance is limited by fiber bandwidth.

§ Maximum transmission distance is based on attenuation of 0.5 dB/km plus a 5 dB buffer for connector and splice losses.

NOTES:

• Single-mode FC connectors are available upon request. Contact the factory for additional information.

• For conformal coated models, replace the first letter F in the model number with the letter C. The conformal coated version of FX82052MSTR-4, for example, is CX82052MSTR-4.

• For models with higher optical power budgets, contact the factory.

C2607M (2/07)

37

Image 37

Contents Ethernet Switch List of Illustrations ContentsList of Tables TX Mode Switch Settings FX Mode Switch SettingsImportant Safety Instructions Risk of Electric Shock Do not Open Radio and Television Interference Regulatory NoticesDescription Product OverviewPOINT-TO-POINT Application with Fiber Redundancy C2607M 2/07 FX82052, -2 Models Multimode Models ModelsSingle-Mode Models† FX82052, -4 Models Multimode ModelsFront Panel Power LED Pelco badge100BASE-FX Status LED Per fiber port a and B Rear Panel 10BASE-T/100BASE-TX Ports 1-5,RJ-45 connectorsFX82052 Rear PANEL, -4 Models 10BASE-T/100BASE-TX Ports 1-5 RJ-45 connectorsPackage Contents InstallationFlow control is disabled by default Autonegotiation is enabled by defaultTable A. TX Mode Switch Settings Setting Fiber Failover ModeFlow control default setting 10BASE-T/100BASE-TX Modes of OperationMode of Operation Table B. FX Mode Switch SettingsDefault setting Secondary fiber linkMounting the FX82052 Module Into a Rack MountingMounting the FX82052 Module Using the Wall Clip Connections FX82052 Connections, -4 Models SC Fiber Connectors ShownFiber connections 10BASE-T/100BASE-TX connectionsFiber Link FX Mode Position Fiber Ports a and B Are Independent FX Mode Position FX Mode Position Fiber Ports a and B Are Independent Check power connection TroubleshootingModule Reseat module or power Supply as necessary Replace power supplyMeaning Optic Fault LED on local Section in this table Indication Fefi On local module Optical signalReplace local module By the remote linkMeaning Possible Cause Corrective Action Optic Fault LED Desired, refer to Setting Table D. Troubleshooting with Rear-Panel IndicatorsAmber If 10BASE-T operation isMeaning Possible Cause Corrective Action Duplex mode Duplex link Duplex modeRefer to Setting If half-duplex mode isGreen Port is set to If 100BASE-TX full-duplex Mode refer to SettingFull-duplex operation is not Flashing green Port is set to Normal or excessiveTable D. Troubleshooting with Rear-Panel Indicators Optic Fault optic signal/laser status per fiber port SpecificationsLink/activity and speed, duplex/collision and speed Multimode 62.5/125 μm FX82052, -2 Models Wavelength Optical MaximumSingle-Mode 9/125 μm FX82052SSTR-2Fibers Illustrates RJ-45 MDI/MDI-X connector pinouts Appendix. RJ-45 Connector PinoutsProduct Warranty and Return Information ISO9001