Network Technologies ST-xU HOW to Disable Operating Modes, Location of jumper block

Page 37

NTI NODEMUX SERIES UNIVERSAL KVM SWITCH

Keyboard Replacement

Should it be necessary to replace the keyboard of one platform with a keyboard of a different platform, the dip-switches will need to be re-configured accordingly. To do this;

1.Power-down the ST-xU by following the proper power-down sequence. That is, turn the CPUs OFF first, then the NTI switch.

2.Replace the keyboard.

3.Re-configure the switches (see Fig. 3 on page 5.) and then power up, following the proper power-up sequence. That is, turn ON power to the NODEMUX first, then to the CPUs.

Note: If the keyboard is being replaced with one from the SAME PLATFORM, it can be hot-swapped without powering- down.

FYI: This procedure applies to legacy NODEMUX switches only. If not a legacy NODEMUX, to change the keyboard configuration from one platform to another, simply unplug the old keyboard, plug in the new keyboard, and power cycle the NODEMUX once.

HOW TO DISABLE OPERATING MODES

NOTE: This section only applies to legacy NODEMUX switches. If the NODEMUX does not have dip switches for RS232 control (page 27) but has a DB-9 RS232 port, this section DOES NOT APPLY.

Three operating modes of the NODEMUX can be disabled if a user desires to do so. The Command Mode can be disabled which would also disable the Scan and Broadcast Modes, or, the Scan and/or Broadcast Modes can be individually disabled leaving the other features in Command Mode enabled.

To disable these operating modes, the user must get access to the jumper block. This block is located close to the dip- switches on the circuit board the keyboards plug into (called the digital board) inside the ST-xU. (See Fig. 36.)

Closeupviewofjumperblockondigitalboard.

RearPanel

JUMPERBLOCK

S BK L

DIPSWITCHES

C RC C

 

A DM D

 

N CD E

 

 

VideoBoard

 

DigitalBoard

FrontPanel

Thejumperblockislocated

LEDboard

belowtheLEDboard.

Overheadviewofvideoboardontopofdigitalboard.

Figure 36- Location of jumper block

If the unit is a rackmount style, the digital board is located directly beneath the cover of the unit, requiring the user to only remove the 9 screws from the cover to get access. With the cover removed, the jumper block will be easy to locate (see Fig. 36). Follow the instructions under "CONFIGURING THE JUMPER BLOCK" (pg. 37) to disable the desired mode(s).

If the unit is in a plastic case, the digital board is located on the bottom of the case, requiring the user to partially disassemble the unit to gain access to the jumper block. If the unit has the OSD option (ST-xU-O), the procedure will be different than the procedure used if the unit does not have the OSD option.

33

Image 37
Contents ST- xU Trademark Table of Contents Table of Figures Introduction FeaturesAvailable Options Supported DevicesMaterials Supplied MaterialsFeatures and Functions To Mount to a Rack Rackmounting InstructionsDip-switch configuration InstallationConnect a PS/2 keyboard and mouse Connect a PS/2 CPU For each CPUSuncpu Connect a touch-screen monitor to an ST-8U-TS-R For Units with Touch-screen support -TSO optionLimitations CascadingCascaded Installation ConfigurationCable Required Basic cascaded master-to-slave cable connectionsOperation Basic Command ModeFront Panel Control Keyboard ControlScan Mode LED will toggle on and OFF Command Functions Contd Function KeystrokeBroadcast Mode LED will toggle on and OFF Xxx from 002 to 255. ie. t002OSD Control Enabling the Security FeatureSecurity Option Administration Mode User Login ModeAdditional Modes Available With Security Configure for Cascading Switch ConfigurationExit Switch Configuration Mode Administrator PasswordTab System Access List User Access FunctionsOSD Command Mode User Name ListCtrl + E Ctrl + M Ctrl + O Command Mode menusCommand Mode Cont’d FunctionKeystroke Edit Mode Edit ModeEsc Enter Search ModeActivate security features Maintenance ModeHelp Mode Touch Maintenance ModeOSD Touch Screen Support Align The Cursor Reset Default ValuesOSD Entry Method Configuration via Dip Switches RS232 Connections and ConfigurationRS232 Connector DB-9 Female Remote ConnectionUnit Address and Loop Back Configuration via OSDUnit Address Loop BackPinout of Matrix-Y-1 cable Command ProtocolFormat RU Aacr Keyboard key layouts KEYBOARD-TO-CPU TranslationLocation of jumper block HOW to Disable Operating ModesCase screws must be removed For models ST-xU no OSDClear access to the jumper block For models ST-xU-O with OSD Component layout in unit with OSD NON-OSD Touch Screen Support Configuring the Jumper BlockOptional-4 and 8 port models only Warranty Information TroubleshootingAlways turn power on in this sequence