Network Technologies ST-xU Administrator Password, Exit Switch Configuration Mode, Tab

Page 22

NTI NODEMUX SERIES UNIVERSAL KVM SWITCH

Note: After configuring an NODEMUX as a slave unit, when the power is cycled the slave NODEMUX will only be controllable through the master NODEMUX it is connected to. Direct OSD menu control of the slave unit will no longer be possible.

In the event the setting is changed by mistake to "slave unit", to change it back to a "stand alone" switch, factory default settings must be restored via a terminal connected to the RS232 control port. See RS232 Control on page 26 for how to restore default settings.

For more on configuring RS232 control, see "RS232 Control" on page 27.

Exit Switch Configuration Mode

Once changes are made to the Switch Configuration menu, press <Enter> and <Y> to save them.

To exit without saving, press <Esc>, then <N>, then <Esc> again. The menu will return to the Administration Mode without saving the changes made.

Changes made will take effect the next time the NODEMUX is power cycled.

To continue setting up a cascaded system of switches, see "Cascaded Installation" on page 10.

Administrator Password

To change the administrator password press <C> from the

Administration Mode menu.

The administrator is able to change the administrator password as needed (see Fig. 21). Two edit fields are available, one for password, the other for verify password. The password can be up to 13 characters in length.

Note: The default password for the administrator is

ADMINISTRATOR.

Figure 21- Administrator password change

Function:

Add character to password string or verify password string

Delete previous character in edited string

Save new password.

Move to next field to be edited

Keystroke:

A-Z

or

Shift

+ A-Z

(Type any upper or lower case

0-9

alphabetical or numeric character)

Backspace

(If Password string and Verify Password string

Enter are different, this command will have no effect, enabling the administrator to correct the password)

Tab

Return to Administration Mode

Esc

 

18

Image 22
Contents ST- xU Trademark Table of Contents Table of Figures Available Options FeaturesIntroduction Supported DevicesMaterials Materials SuppliedFeatures and Functions Rackmounting Instructions To Mount to a RackInstallation Dip-switch configurationConnect a PS/2 keyboard and mouse For each CPU Connect a PS/2 CPUSuncpu For Units with Touch-screen support -TSO option Connect a touch-screen monitor to an ST-8U-TS-RCascading LimitationsConfiguration Cascaded InstallationBasic cascaded master-to-slave cable connections Cable RequiredFront Panel Control Basic Command ModeOperation Keyboard ControlBroadcast Mode LED will toggle on and OFF Command Functions Contd Function KeystrokeScan Mode LED will toggle on and OFF Xxx from 002 to 255. ie. t002OSD Control Enabling the Security FeatureSecurity Option Administration Mode User Login ModeAdditional Modes Available With Security Switch Configuration Configure for CascadingExit Switch Configuration Mode Administrator PasswordTab OSD Command Mode User Access FunctionsSystem Access List User Name ListCommand Mode menus Ctrl + E Ctrl + M Ctrl + OCommand Mode Cont’d FunctionKeystroke Edit Mode Edit ModeSearch Mode Esc EnterMaintenance Mode Activate security featuresHelp Mode Touch Maintenance ModeOSD Touch Screen Support Align The Cursor Reset Default ValuesOSD Entry Method RS232 Connector DB-9 Female RS232 Connections and ConfigurationConfiguration via Dip Switches Remote ConnectionConfiguration via OSD Unit Address and Loop BackLoop Back Unit AddressCommand Protocol Pinout of Matrix-Y-1 cableFormat RU Aacr KEYBOARD-TO-CPU Translation Keyboard key layoutsHOW to Disable Operating Modes Location of jumper blockFor models ST-xU no OSD Case screws must be removedClear access to the jumper block For models ST-xU-O with OSD Component layout in unit with OSD NON-OSD Touch Screen Support Configuring the Jumper BlockOptional-4 and 8 port models only Warranty Information TroubleshootingAlways turn power on in this sequence