Network Technologies ST-xU operation manual Materials Supplied

Page 6

NTI NODEMUX SERIES UNIVERSAL KVM SWITCH

MATERIALS

Materials Supplied:

NTI ST-xU UNIVERSAL KVM Switch

IEC Line cord, country specific

CD with a pdf file of this manual

Materials Not Supplied, but REQUIRED:

A set of 2 cables for each CPU being connected to the switch:

PS/2 CPU to Switch

- VEXT-xx-MM for video interface

 

- VKTINT-xx-MM for keyboard and mouse interface

 

OR

SUN CPU to Switch

- VEXT-xx-MM for video interface

 

- 13W3M-15HDF (adapter for 13W3 to 15HD)

 

- SKTINT-xx-MM for keyboard/mouse interface

 

OR

MAC CPU to Switch

- VEXT-xx-MM for video interface

-15DM-15HDF (adapter for 15D to 15HD)

-MKTINT-xx-MM for keyboard/mouse interface

One of the following cables must be used to connect the input devices (keyboard and mouse):

PS/2 keyboard & mouse

-

VKTINT-1

 

 

OR

 

SUN keyboard/mouse

None needed. SUN keyboard plugs directly in.

 

 

OR

 

MAC keyboard/mouse

-

MKTINT-1

OPTIONAL:

REXT-SR-xx

- RMT Extension cable -for cascading switches- legacy-to-legacy

REXT-SR15-xx

-

RMT Extension cable- for cascading switches- legacy-to-current

REXT-SR45-xx

-

RMT Extension cable- for cascading switches- current-to-current

Where:

xxis the length of the cable in feet.

MMindicates male-to-male connector, and

FYI : "legacy" switches have hardware-based keyboard, mouse, and RS232 configuration "current" switches have software-based keyboard, mouse, and RS232 configuration

Cables can be purchased from Network Technologies Inc by calling 800-RGB-TECH (800-742-8324) or (330)-562- 7070.

2

Image 6
Contents ST- xU Trademark Table of Contents Table of Figures Available Options FeaturesIntroduction Supported DevicesMaterials Materials SuppliedFeatures and Functions Rackmounting Instructions To Mount to a RackInstallation Dip-switch configurationConnect a PS/2 keyboard and mouse For each CPU Connect a PS/2 CPUSuncpu For Units with Touch-screen support -TSO option Connect a touch-screen monitor to an ST-8U-TS-RCascading LimitationsConfiguration Cascaded InstallationBasic cascaded master-to-slave cable connections Cable RequiredFront Panel Control Basic Command ModeOperation Keyboard ControlBroadcast Mode LED will toggle on and OFF Command Functions Contd Function KeystrokeScan Mode LED will toggle on and OFF Xxx from 002 to 255. ie. t002Enabling the Security Feature OSD ControlSecurity Option User Login Mode Administration ModeAdditional Modes Available With Security Switch Configuration Configure for CascadingAdministrator Password Exit Switch Configuration ModeTab OSD Command Mode User Access FunctionsSystem Access List User Name ListCommand Mode menus Ctrl + E Ctrl + M Ctrl + OCommand Mode Cont’d FunctionKeystroke Edit Mode Edit ModeSearch Mode Esc EnterMaintenance Mode Activate security featuresTouch Maintenance Mode Help ModeOSD Touch Screen Support Reset Default Values Align The CursorOSD Entry Method RS232 Connector DB-9 Female RS232 Connections and ConfigurationConfiguration via Dip Switches Remote ConnectionConfiguration via OSD Unit Address and Loop BackLoop Back Unit AddressCommand Protocol Pinout of Matrix-Y-1 cableFormat RU Aacr KEYBOARD-TO-CPU Translation Keyboard key layoutsHOW to Disable Operating Modes Location of jumper blockFor models ST-xU no OSD Case screws must be removedClear access to the jumper block For models ST-xU-O with OSD Component layout in unit with OSD Configuring the Jumper Block NON-OSD Touch Screen SupportOptional-4 and 8 port models only Troubleshooting Warranty InformationAlways turn power on in this sequence