Paradyne 7924 manual Making Changes from the Terminal Interface

Page 20

Customizing DSX-1-Compatible Units

This guide depicts the system terminal menus as they appear from a CP unit.

This is the default configuration for Model 7924 standalone units.

Making Changes from the Terminal Interface

The Board Configuration menu displays the current board software and hardware settings. It also allows you to change certain parameters on the board.

This function is affected by the status of the switchpack (DIP switch control) setting.

HWhen operating in Terminal Mode (the system default) you can make configuration changes through the terminal menus.

HWhen operating in Switchpack Mode, you can display configuration parameters using the terminal menus, but any configuration changes must be made using the switchpacks and jumpers on the board hardware. Refer to Making Changes in Switchpack Mode on page 4-5.

To access the Board Configuration menu, enter 3 at the Main Menu Command prompt.

Command3

 

Board Configuration:

 

1)

HDSL Card Type

± CP

 

HDSL Rate Type

± T1

2)

Loops Enabled

± Dual Loop (Loops A and B)

3)

T1 Line Encode

± B8ZS

4)

Framing

± D4

5)

Line Build Out

± 0 to 133 feet, 0dB

 

HDSL FW Rev

± 07

 

AT+T FW Rev

± 1.17

 

CP Serial #

± 085561

±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±È±±±±

1±5)

Board Configuration

6)

Switch pack Definitions

7)

Line Build±Out Definitions

?)

Redisplays this menu

Q)

Quit

Config

Possible values for each parameter are listed in Table 4-1. See Appendix A, Worksheets, for help in selecting the appropriate configuration options for your application.

4-2

October 1997

7924-A2-GB20-30

Image 20
Contents Model 7924 Standalone T1 Hdsl Termination Unit Trademarks Warranty, Sales, and Service InformationCopyright  1997 Paradyne Corporation All rights reserved Important Safety Instructions EMI Warnings Contents Customizing V.35-Compatible Units Cable Pin Assignments IiiDocument Summary About This GuideDocument Purpose and Intended Audience Product-Related Documents Document Number Document TitleAbout HotWire Model Termination Units HotWire 7924-A1 Models and FeaturesModel Number Features Typical Configurations Campus Network ApplicationsDCS Cellular Network Access User Interface TypesOverview Installing the UnitPackage Checklist for HotWire Model 7924-A1 Connecting to the Network Connecting Power to the UnitProcedure DSX-1-Compatible HotWire 7924 ± Rear PanelConnecting to a System Terminal Using Terminal and Switchpack ModesChoosing an Interface Mode Switching Between Terminal and Switchpack Modes Accessing Configuration Options Customizing DSX-1-Compatible UnitsMaking Changes from the Terminal Interface DSX-1-Compatible Units Configuration Options 1 Hdsl Card TypeDSX-1-Compatible Units Configuration Options 2 Making Changes in Switchpack Mode Displaying Switchpack DefinitionsSwitchpack Settings for Line Build OUT Displaying Line Build-Out DefinitionsCustomizing V.35-Compatible Units Customizing V.35-Compatible Units V.35-Compatible Units Configuration Options ± 6 x 64 384 kbps ± No change to rateMaking Changes in Switchpack Mode CO/CP OFF=CP, ON=CO Monitoring the Unit What to MonitorBoard Status for V.35-Compatible Unit Board StatusBoard Status for DSX-1-Compatible Unit Performance Statistics Performance Statistics for DSX-1-Compatible Unit Performance Statistics for V.35-Compatible UnitRemote Unit Information Meaning Front Panel LEDsDSX-1-Compatible Unit Compatible Unit Understanding Loopback Tests TestingDetecting a Problem Local Loopbacks Local Loopback, Initiated at the CO UnitRemote Loopbacks Remote Loopback, Initiated at the CO UnitStarting and Stopping Loopbacks Resetting the Unit Worksheets DSX-1-to-DSX-1 Configuration DSX-1-to-V.35 Configuration LANPayload Rate DSX-1 T1 DS0s Used Unframed OperationTime Slot DS0 Assignments DSX-1-Compatible Units Configuration Worksheet Compatible Units Configuration WorksheetCable Pin Assignments Terminal Connection Cable Pin AssignmentsHdsl Loop Connection Cable Pin Assignments PinT1 Network Connection Cable Pin Assignments Function Description Connection Cable Pin AssignmentsDirection Code Pin Name DSX-1-Compatible Units Switchpacks and JumpersJumper Pins Factory-Setting Switchpacks and Jumpers Compatible Units Jumper P8 Factory defaults GlossaryGL-1 COM portLoopback ResetGL-2 Index IN-1IN-2 Index