Paradyne 8510 RADSL, 8310 MVLt manual Filters Options 2, IP Filters IP Filter Configuration

Page 56

8310 MVL and 8510 RADSL Card Configuration

Table 4-6. Filters Options (2 of 2)

IP Filters (IP Filter Configuration) (continued)

A-G-A

 

 

Filter Name ± Up to 12 characters.

Default Filter Action ± Forward (Packet)/Discard (Packet) (Default = Forward). The Default Filter Action applies when there is no match or the filter has no rules configured.

DHCP Filter Action ± Forward (Packet)/Discard (Packet) (Default = Forward). Forwards or discards DHCP transaction traffic on a particular DSL port.

Rule # ± Up to 33 rules can be configured for each filter. The rule number is automatically assigned. The rules are reviewed sequentially. The most common rules should be entered first.

Source Address ± nnn.nnn.nnn.nnn format. Enter valid host or network IP address. If 0.0.0.0 is entered, Source Comparison is ignored.

NOTE: For additional information, refer to Configuring Subnet Addressing in Chapter 3, Configuring the Hotwire DSLAM.

Source Mask ± nnn.nnn.nnn.nnn format. If you specify a source subnet mask of 0.0.0.0, the system skips the source address comparison.

Source Comparison ± Enabled/Disabled (Default = Disabled). When Source Comparison is disabled, the comparison is ignored.

Source Port # ± 0±65535 (Default = 0).

Comparison Type (for source information) ± Ignore ± Do not do a comparison. To do a comparison on the port number specified in the packet and the rule, specify one of the following: Ignore ± Ignore ports, EQ ± Equal to, NEQ ± Not Equal to, GT ± Greater than, LT ± Less than, In_Range ± Within the specified range, Out_Range ± Outside of the specified range (Default = Ignore).

Max. Source Port No. ± 0±65535. Appears only when the source comparison type is In Range or Out of Range.

Destination Address ± nnn.nnn.nnn.nnn format.

Destination Mask ± nnn.nnn.nnn.nnn format. If you specify a destination subnet mask of 0.0.0.0, the system skips the destination address comparison.

Destination Comparison ± Enabled/Disabled (Default = Disabled). When Destination Comparison is disabled, the comparison is ignored.

Destination Port # ± 0±65535 (Default = null).

Comparison Type (for destination information) ± Ignore ± Ignore ports, EQ ± Equal to, NEQ ± Not Equal To, GT ± Greater than, LT ± Less than, In_Range ± Within the specified range, Out_Range ± Outside of the specified range.

Max. Destination Port No. ± 2±65535. Appears only when the destination port comparison type is In Range or Out of Range.

Action ± For a rule, TCP, UDP, or ICMP traffic will be forwarded or discarded provided other conditions have been satisfied.

HTCP ± Forward/Discard (Default = Forward).

HUDP ± Forward/Discard (Default = Forward).

HICMP ± Forward/Discard (Default = Forward).

Delete Rule ± Yes/No (Default = No).

4-18

January 1999

8000-A2-GB26-10

Page 55 Page 57
Image 56
Page 55 Page 57
Contents HOTWIRE Dslam for 8310 MVL and 8510 Radsl Cards Copyright E 1999 Paradyne Corporation All rights reserved Contents Configuring the Hotwire Dslam Traps Contents About This Guide Document Purpose and Intended AudienceDocument Summary Section DescriptionProduct-Related Documents Document Number Document TitleViii Hotwire Dslam System Description What is the Hotwire DSLAM?Optional Hotwire Dslam ComponentsCentral Office CO Hotwire Dslam Chassis InputFront View of a Hotwire 8800 or 8810 Dslam Chassis Radsl or MVL Card Hotwire Dslam FeaturesMCC Card Software Functionality Levels of AccessConfiguring the DSL Cards Monitoring the DSL Cards Troubleshooting and Diagnostics Hotwire Menus and Screens OverviewComponents of a Hotwire Menu Menu and Screen FormatsComponents of a Hotwire Screen Commonly Used Navigation Keys Keys DefinitionHotwire Menu Hierarchy Hotwire Chassis Main MenuHotwire ± MCC Menu Hotwire ChassisHotwire ± DSL Menu Hotwire DSLDiagnostics ApplicationsDSL Card Configuration Menu Logging In to the System DSL Card Monitoring MenuReviewing the Levels of Access User Login ScreenCard Selection Screen Column Position Display Description Heading D U X XAccessing the Hotwire ± DSL Menu Exiting from the SystemManually Logging Out Automatically Logging OutConfiguring the Hotwire Dslam Service DomainDomain Types Management DomainConfiguring the DSL Cards For each DSL card, to SeeConfiguring VNIDs on a DSL Card Configuring the Active Vnid on each DSL Port Configuring Static Users Addressing a Location Using DhcpConfiguring Subnet Addressing Configuring Subnet MasksConfiguring IP Filter Rules Configuring the Hotwire Dslam MVL and 8510 Radsl Card Configuration DSL Configuration Card Status ScreensCard Status Options 1 Card Info Card InformationTime/Date Nvram ClearNvram Cfg Loader Nvram Configuration Loader Card ResetCard Status Options 2 DOS MachineCard Status Options 3 Download Code Download Code and Apply Download F a and BDownload Code a or Apply Download B Apply Download BEthernet Port DSL Configuration Ports ScreensPorts Options 1 Ports Options 2 DSL Ports Radsl Parameters 8510 Radsl CardPorts Options 3 DSL Ports MVL Parameters 8310 MVL CardDSL Configuration Interfaces Screens Control Control Interfaces Interfaces OptionsGeneral General Interfaces DSL Configuration Users Screens DSL Configuration Bridge ScreensBridge Options 1 General General Bridge ParametersCard Vnid Port VnidBridge Options 2 Client VnidBridge Options 3 ARP Entry Add ARP Entry BDSL Configuration Service Node Screens Service Node Options SN ConfigurationDSL Configuration Filters Screen IP Filters IP Filter Table IP Filters IP Filter Configuration screenFilters Options 1 Destination Address ± nnn.nnn.nnn.nnn format IP Filters IP Filter ConfigurationFilters Options 2 Monitoring the Hotwire Dslam DSL Monitoring Card Status ScreensCard Info General Card Information Login HistoryCard Status Options Syslog Screen Example Active List Active Ports List DSL Monitoring Physical Layer ScreensPhysical Layer Options 1 Physical Layer Options 2 Ethernet Stats Ethernet StatisticsInitialized EtherHDLC Ports ± s1c, s1d, s1e, or s1f Physical Layer Options 3EtherHDLC Stats EtherHDLC Statistics Physical Layer Options 4 DSL Link Perf DSL Link Performance SummaryCustomer Data Physical Layer Options 5DSL Perf Stats DSL Performance Stats DSL Xmit Status DSL Transmit Stats DSL Error StatsPhysical Layer Options 6 DSL Monitoring Interfaces Screens Status Interface Status Monitor Interfaces OptionsActive List Active Interfaces List DSL Network Protocol Screens UDP Statistics Network Protocol Options 1Socket Statistics Network Protocol Options 2 TCP Statistics TCP Data StatisticsIP Statistics Network Protocol Options 3TCP Connection Statistics Snmp Statistics Network Protocol Options 4Icmp Statistics Icmp Packet Statistics Snmp Authentication Statistics Network Protocol Options 5DSL Bridge Screens Bridge TableItem to Display ± Entry number MAC TableClient Vnid ARP TableDSL SN Information Screen Default filter action ± Forward/discard DSL Monitoring IP Filters ScreenIP Filters Filter TableDiagnostics and Troubleshooting Diagnostic ScreensDiagnostics Options Alarms Card AlarmsSelftest DSL Packet Echo TestTroubleshooting Checking AlarmsMajor Alarms 1 Action No Response at StartupMajor Alarms 2 Action Minor Alarms 1 Action Margin ThresholdThreshold Minor Alarms 2 ActionLink Down Network Problems High-Level TroubleshootingIf the Client cannot Ping the Gateway Router Then Client-to-Service Node SegmentClient Cannot Ping the Gateway Router Client Cannot Reach Service Node Client-to-Service Node Segment Layer SolutionLayer 1 ± PhysicalLayer 1 ± Physical Service Node-to-DSLAM Segment 1 Layer SolutionClient Cannot Reach Dslam Network Service Node-to-DSLAM Segment 2 Layer SolutionLayer 2 ± Client Cannot Reach IPC DSLAM-to-IPC Segment Layer Solution Movefromdef=1IPC-to-Router Segment Layer Solution Client Cannot Reach RouterCannot Upload Configurations to a Unix Server Router-to-IPC Segment Layer SolutionPerformance Issues ± Viewing Network Statistics Examining Performance Issues Go ToDownload Code Download Code Download Only System Automatic Immediate ApplyEvent Severity Comment Trap # TrapsDSL Card Traps Traps MIB Traps Glossary Default route Dhcp Relay AgentDhcp Server DomainHost Host routesHub InternetService Node OpenLane DCEManager PacketStatic route Subnet addressSubnet mask TelnetGL-6 Index IN-1IN-2
Top Page Image Contents