Patton electronic 3088 user manual System Reset Mode, Software Upgrades

Page 12

The two sets of DIP switches on the underside of the Model 3088 are referred to as S1 and S2. As shown in ﬁgure 3, the orientation of all DIP switches is the same with respect to “ON” and “OFF” positions

ON

1 2 3 4 5 6 7 8

ON

OFF

Figure 3. Close-up of conﬁguration switches (all sets are identical appearance)

4.2 SYSTEM RESET MODE

System reset mode is entered by switching all DIP switches to the OFF position and power cycling the unit. A VT100 emulator conﬁgured for 19,200 kbps/1 stop bit/ no parity/ XON-XOFF ﬂow control can be used to access the console. Upon restart, you will see the message

“Reset Mode”.

System reset mode provides two functions:

•Software upgrades

•Conﬁguration reset to factory defaults

Software Upgrades

The software is upgraded by waiting for the “Reset Mode” message. Then, the user can send an Intel HEX ﬁle supplied by Patton. After the VT100 emulator has ﬁnished sending this ﬁle, the 3088 will respond with a message stating how many errors were detected. The user may then set the DIP switches to the desired conﬁguration and power cycle the unit to run the upgraded software.

12

Image 12

Contents User Manual Contents Operation Remote Console Manual InformationCompliance Information Radio and TV Interference FCC Part 68 Acta StatementIndustry Canada Notice CE NoticeWarranty Information ServiceTel +1 301 Email support@patton.com Features General InformationDescription Configuration Model 3088 3088/D version shownParameter Description Possible Default Values OFF, LAL Parameter Description Possible Default Configuring the DIP SwitchesSystem Reset Mode Software UpgradesConﬁguration Reset to Factory Defaults DIP Switch SettingsPosition Function Factory Default S1-8 TX Clock Setting Description S1-7 S1-1 Data RateS1-7 S1-6 S1-5 S1-4 S1-3 S1-2 S1-1 Data Rate Kbps 1920 S2-6 Setting S2-5 S2-4 Clock ModeS2-5 S2-4 Clock Mode Description LoopsS2-1 Front Panel Switches S2-3 Annex A/BS2-3 Annex S2-2 Line ProbePage DSL Line Condition Good or Poor CRCHelp Commands System Conﬁguration CommandsSystem show clockmode Shows the clock mode System Status CommandsDSL Conﬁguration Commands Startup Delay Interval Interval totintDSL Status Commands Page Example Command Line Interface Session Remote ConsoleRocketlink Plug ‘N’ Play 3096RC Installation Connecting the Twisted Pair InterfaceConnecting the Model 3088/CA Serial Interface Connecting the Model 3088/CA V.35 to a DTE DeviceConnecting the Model 3088/CA V.35 to a DCE Device Connecting the Model 3088/D X.21 Serial InterfaceConnecting the Model 3088/D X.21 to a DCE or DTE Device Connecting the Model 3088/D to X.21 DTE or DCE Opening the CaseConnecting Power POWER-UP Power GreenOperation LED Status MonitorsTerm Green 3088/D with the X.21 interfaceTM/ER Red Test ModesLocal Analog Loopback diagram PatternsHow to Connect Remote Console Manual InformationEstablishing a Remote Console Session Page System show status command shows that DSL link is not up How to DisconnectDifferences in Local and Remote Control Session Behavior LAL Model 3088 Software Upgrade Feature Reset Configuration to Factory Defaults Serial Connector DiagnosticsAppendix a Clocking ModesPower ComplianceTransmission Line Line CodingLine Interface 14 G.SHDSL Physical ConnectionEnvironment Appendix B Model # DescriptionPin # Signal Appendix CPin Signal Appendix D