Patton electronic 3088 user manual Industry Canada Notice, CE Notice

Page 5

the telephone network, the telephone company may request that you dis- connect the equipment until the problem is resolved.

Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information.

1.3 INDUSTRY CANADA NOTICE

This equipment meets the applicable Industry Canada Terminal Equip- ment Technical Specifications. This is confirmed by the registration num- ber. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicat- ing that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.

This Declaration of Conformity means that the equipment meets certain telecommunications network protective, operational and safety require- ments. The Department does not guarantee the equipment will operate to the user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. In some cases, the com- pany's inside wiring associated with a single line individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above condition may not prevent degradation of service in some situa- tions. Repairs to some certified equipment should be made by an autho- rized maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunc- tions, may give the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for their own pro- tection that the ground connections of the power utility, telephone lines and internal metallic water pipe system, are connected together. This protection may be particularly important in rural areas.

1.4 CE NOTICE

This equipment conforms to the requirements of Council Directive 1999/ 5/EC on the approximation of the laws of the member states relating to Radio and Telecommunication Terminal Equipment and the mutual rec- ognition of their conformity.

5

Image 5
Contents User Manual Contents Remote Console Manual Information OperationFCC Part 68 Acta Statement Compliance Information Radio and TV InterferenceCE Notice Industry Canada NoticeTel +1 301 Email support@patton.com Warranty InformationService Description FeaturesGeneral Information Model 3088 3088/D version shown ConfigurationParameter Description Possible Default Values OFF, LAL Configuring the DIP Switches Parameter Description Possible DefaultSoftware Upgrades System Reset ModePosition Function Factory Default Configuration Reset to Factory DefaultsDIP Switch Settings S1-7 S1-6 S1-5 S1-4 S1-3 S1-2 S1-1 Data Rate Kbps S1-8 TX Clock Setting DescriptionS1-7 S1-1 Data Rate 1920 S2-5 S2-4 Clock Mode S2-6 SettingS2-5 S2-4 Clock Mode Description LoopsS2-3 Annex A/B S2-1 Front Panel SwitchesS2-3 Annex S2-2 Line ProbePage CRC DSL Line Condition Good or PoorSystem Configuration Commands Help CommandsSystem Status Commands System show clockmode Shows the clock modeStartup Delay Interval Interval totint DSL Configuration CommandsDSL Status Commands Page Remote Console Example Command Line Interface SessionRocketlink Plug ‘N’ Play 3096RC Connecting the Twisted Pair Interface InstallationConnecting the Model 3088/CA V.35 to a DTE Device Connecting the Model 3088/CA Serial InterfaceConnecting the Model 3088/D X.21 to a DCE or DTE Device Connecting the Model 3088/CA V.35 to a DCE DeviceConnecting the Model 3088/D X.21 Serial Interface Opening the Case Connecting the Model 3088/D to X.21 DTE or DCEConnecting Power Power Green POWER-UPOperation LED Status Monitors3088/D with the X.21 interface Term GreenTM/ER Red Test ModesPatterns Local Analog Loopback diagramEstablishing a Remote Console Session How to ConnectRemote Console Manual Information Page How to Disconnect System show status command shows that DSL link is not upDifferences in Local and Remote Control Session Behavior LAL Model 3088 Software Upgrade Feature Reset Configuration to Factory Defaults Diagnostics Serial ConnectorAppendix a Clocking ModesCompliance PowerTransmission Line Line CodingEnvironment Line Interface14 G.SHDSL Physical Connection Model # Description Appendix BAppendix C Pin # SignalAppendix D Pin Signal