Patton electronic 3088 user manual

Page 18

•Circuit ID: The circuit ID communicated to other units via EOC. EOC (Embedded Operations Channel) is an out-of-band channel speciﬁed in the G.991.2 standard for SHDSL. We use standard EOC messages for our remote loopback. The 3088 also supports proprietary EOC messages that allow a 3096RC to conﬁgure it.

•Clock Mode: The following options are available:

–Internal: The 3088 provides the clock to both the serial and DSL interfaces.

–External: The serial interface provides the clock used for the DSL interface (V.35 only).

–Receive Recover: The clock recovered from the DSL is provided to the serial interface.

•Data Rate: Both the serial and DSL data rates are set by specifying the number of 64k timeslots.

•Annex: Either G.991.2 Annex A or Annex B.

•DSL Error Monitor Max Interval Errors: The number of errors allowed in an interval before considering the interval errored. A value of ‘0’ disables the DSL error monitor.

•DSL Error Monitor Interval Time: The length in seconds of an interval.

•DSL Error Monitor Interval Count: The number of errored intervals allowed before restarting the DSL link.

•DSL Error Monitor Total Intervals: The number of intervals to inspect before disabling the error monitor.

•DSL Error Monitor Startup Delay: The length in seconds to wait after the DSL link is established before starting the error monitor.

•Test Modes: Loopbacks (LAL or RDL) and PRBS (pseudo random binary sequence) BER tests (511 or 511 with errors)

•Line Probe: Enable or disable Line Probe for rate adaptive applications.

The following status information is available through the command line interface:

• LEDs: Which software controlled LEDs are currently on.

18

Image 18

Contents User Manual Contents Operation Remote Console Manual InformationCompliance Information Radio and TV Interference FCC Part 68 Acta StatementIndustry Canada Notice CE NoticeWarranty Information ServiceTel +1 301 Email support@patton.com Features General InformationDescription Configuration Model 3088 3088/D version shownParameter Description Possible Default Values OFF, LAL Parameter Description Possible Default Configuring the DIP SwitchesSystem Reset Mode Software UpgradesConﬁguration Reset to Factory Defaults DIP Switch SettingsPosition Function Factory Default S1-8 TX Clock Setting Description S1-7 S1-1 Data RateS1-7 S1-6 S1-5 S1-4 S1-3 S1-2 S1-1 Data Rate Kbps 1920 S2-5 S2-4 Clock Mode Description S2-6 SettingS2-5 S2-4 Clock Mode LoopsS2-3 Annex S2-1 Front Panel SwitchesS2-3 Annex A/B S2-2 Line ProbePage DSL Line Condition Good or Poor CRCHelp Commands System Conﬁguration CommandsSystem show clockmode Shows the clock mode System Status CommandsDSL Conﬁguration Commands Startup Delay Interval Interval totintDSL Status Commands Page Example Command Line Interface Session Remote ConsoleRocketlink Plug ‘N’ Play 3096RC Installation Connecting the Twisted Pair InterfaceConnecting the Model 3088/CA Serial Interface Connecting the Model 3088/CA V.35 to a DTE DeviceConnecting the Model 3088/CA V.35 to a DCE Device Connecting the Model 3088/D X.21 Serial InterfaceConnecting the Model 3088/D X.21 to a DCE or DTE Device Connecting the Model 3088/D to X.21 DTE or DCE Opening the CaseConnecting Power Operation POWER-UPPower Green LED Status MonitorsTM/ER Red Term Green3088/D with the X.21 interface Test ModesLocal Analog Loopback diagram PatternsHow to Connect Remote Console Manual InformationEstablishing a Remote Console Session Page System show status command shows that DSL link is not up How to DisconnectDifferences in Local and Remote Control Session Behavior LAL Model 3088 Software Upgrade Feature Reset Configuration to Factory Defaults Appendix a Serial ConnectorDiagnostics Clocking ModesTransmission Line PowerCompliance Line CodingLine Interface 14 G.SHDSL Physical ConnectionEnvironment Appendix B Model # DescriptionPin # Signal Appendix CPin Signal Appendix D