Patton electronic 3088 user manual Conﬁguration Reset to Factory Defaults, DIP Switch Settings

Page 13

Conﬁguration Reset to Factory Defaults

To recover from a forgotten password, the user may reset the unit to its factory conﬁguration. After seeing the “Reset Mode” message, the user should type the ‘*’ key. This will result in a ‘:’ prompt. At the prompt, the user should enter the command reset. This will restore the unit to the fac- tory conﬁguration. The unit can then be restarted with the settings

in place.

4.3 DIP SWITCH SETTINGS

The 3088 can be conﬁgured with DIP switches. If the DIP switches are set to anything other than all ON, then the unit will be in DIP switch con- ﬁguration. In DIP switch conﬁguration, the console and EOC cannot be used to change conﬁguration.

The following table describes the DIP switch functions.

Position	Function	Factory Default

S1-8	TX Clock	ON	Normal
S1-7	Data Rate	ON	256K

S1-6		ON

S1-5		ON

S1-4		ON

S1-3		ON

S1-2		OFF

S1-1		OFF

S2-8	Reserved	OFF

S2-7		OFF

S2-6	DTE Loops	OFF	Disabled

S2-5	Clock Mode	OFF	Receive-
			Recover
S2-4		ON	Recover

S2-3	Annex	OFF	Annex B

S2-2	Line Probe	ON	Disabled

S2-1	Front Panel Switches	OFF	Enabled

13

Image 13

Contents User Manual Contents Remote Console Manual Information OperationFCC Part 68 Acta Statement Compliance Information Radio and TV InterferenceCE Notice Industry Canada NoticeService Warranty InformationTel +1 301 Email support@patton.com General Information FeaturesDescription Model 3088 3088/D version shown ConfigurationParameter Description Possible Default Values OFF, LAL Configuring the DIP Switches Parameter Description Possible DefaultSoftware Upgrades System Reset ModeDIP Switch Settings Conﬁguration Reset to Factory DefaultsPosition Function Factory Default S1-7 S1-1 Data Rate S1-8 TX Clock Setting DescriptionS1-7 S1-6 S1-5 S1-4 S1-3 S1-2 S1-1 Data Rate Kbps 1920 S2-5 S2-4 Clock Mode S2-6 SettingS2-5 S2-4 Clock Mode Description LoopsS2-3 Annex A/B S2-1 Front Panel SwitchesS2-3 Annex S2-2 Line ProbePage CRC DSL Line Condition Good or PoorSystem Conﬁguration Commands Help CommandsSystem Status Commands System show clockmode Shows the clock modeStartup Delay Interval Interval totint DSL Conﬁguration CommandsDSL Status Commands Page Remote Console Example Command Line Interface SessionRocketlink Plug ‘N’ Play 3096RC Connecting the Twisted Pair Interface InstallationConnecting the Model 3088/CA V.35 to a DTE Device Connecting the Model 3088/CA Serial InterfaceConnecting the Model 3088/D X.21 Serial Interface Connecting the Model 3088/CA V.35 to a DCE DeviceConnecting the Model 3088/D X.21 to a DCE or DTE Device Opening the Case Connecting the Model 3088/D to X.21 DTE or DCEConnecting Power Power Green POWER-UPOperation LED Status Monitors3088/D with the X.21 interface Term GreenTM/ER Red Test ModesPatterns Local Analog Loopback diagramRemote Console Manual Information How to ConnectEstablishing a Remote Console Session Page How to Disconnect System show status command shows that DSL link is not upDifferences in Local and Remote Control Session Behavior LAL Model 3088 Software Upgrade Feature Reset Configuration to Factory Defaults Diagnostics Serial ConnectorAppendix a Clocking ModesCompliance PowerTransmission Line Line Coding14 G.SHDSL Physical Connection Line InterfaceEnvironment Model # Description Appendix BAppendix C Pin # SignalAppendix D Pin Signal