Patton electronic 3088 Power, Compliance, Transmission Line, Line Coding, Line Rates DSL Line

Page 44

Term (Green)

The Term LED glows solid under the following circumstances:

•3088/CA with V.35 interface: If the serial interface has asserted DTR

•3088/D with the X.21 interface:

–Conﬁgured as DCE : Indicates that the “Control” signals have been asserted.

–Conﬁgured as DTE : Indicates that the “Indication” signals have been asserted

TM/ER (Red)

The Test Mode/Error (TM/ER) LED is used to indicate that a test mode is in progress or an error has been detected. It blinks once every second while a test mode is starting. It glows solid while a test mode is in progress. It blinks once if an error is detected either during a test mode, or in normal DSL operation.

A.7 CONFIGURATION

Externally accessible DIP switches or SNMP managed through 3096RC

A.8 POWER

5 VDC from external desk top power supply, 90-260VAC, 50-60 Hz (Uni- versal Input), 10W

A.9 COMPLIANCE

FCC Part 15, CE, ACTA (FCC Part 68): IC-CS03

A.10 TRANSMISSION LINE

Single Twisted Pair

A.11 LINE CODING

TC-PAM (Trellis Coded Pulse Amplitude Modulation)

A.12 LINE RATES (DSL LINE)

All nx64 rates from 64 kbps up to 4.6 Mbps

44

Image 44

Contents User Manual Contents Operation Remote Console Manual InformationCompliance Information Radio and TV Interference FCC Part 68 Acta StatementIndustry Canada Notice CE NoticeTel +1 301 Email support@patton.com Warranty InformationService Description FeaturesGeneral Information Configuration Model 3088 3088/D version shownParameter Description Possible Default Values OFF, LAL Parameter Description Possible Default Configuring the DIP SwitchesSystem Reset Mode Software UpgradesPosition Function Factory Default Conﬁguration Reset to Factory DefaultsDIP Switch Settings S1-7 S1-6 S1-5 S1-4 S1-3 S1-2 S1-1 Data Rate Kbps S1-8 TX Clock Setting DescriptionS1-7 S1-1 Data Rate 1920 S2-6 Setting S2-5 S2-4 Clock ModeS2-5 S2-4 Clock Mode Description LoopsS2-1 Front Panel Switches S2-3 Annex A/BS2-3 Annex S2-2 Line ProbePage DSL Line Condition Good or Poor CRCHelp Commands System Conﬁguration CommandsSystem show clockmode Shows the clock mode System Status CommandsDSL Conﬁguration Commands Startup Delay Interval Interval totintDSL Status Commands Page Example Command Line Interface Session Remote ConsoleRocketlink Plug ‘N’ Play 3096RC Installation Connecting the Twisted Pair InterfaceConnecting the Model 3088/CA Serial Interface Connecting the Model 3088/CA V.35 to a DTE DeviceConnecting the Model 3088/D X.21 to a DCE or DTE Device Connecting the Model 3088/CA V.35 to a DCE DeviceConnecting the Model 3088/D X.21 Serial Interface Connecting the Model 3088/D to X.21 DTE or DCE Opening the CaseConnecting Power POWER-UP Power GreenOperation LED Status MonitorsTerm Green 3088/D with the X.21 interfaceTM/ER Red Test ModesLocal Analog Loopback diagram PatternsEstablishing a Remote Console Session How to ConnectRemote Console Manual Information Page System show status command shows that DSL link is not up How to DisconnectDifferences in Local and Remote Control Session Behavior LAL Model 3088 Software Upgrade Feature Reset Configuration to Factory Defaults Serial Connector DiagnosticsAppendix a Clocking ModesPower ComplianceTransmission Line Line CodingEnvironment Line Interface14 G.SHDSL Physical Connection Appendix B Model # DescriptionPin # Signal Appendix CPin Signal Appendix D