Patton electronic user manual Configuration, Model 3088 3088/D version shown

Page 8

4.0 CONFIGURATION

The Model 3088 (see ﬁgure 1) has two conﬁguration modes, DIP switch and software.

Figure 1. Model 3088 (3088/D version shown)

DIP switch conﬁguration mode is entered by starting the unit with the DIP switches in any position other than all OFF or all ON. In DIP switch conﬁgu- ration mode, the DIP switch settings are read at system startup and used to conﬁgure the unit. Once the unit has started in DIP switch mode it will remain in DIP switch mode, and its settings cannot be changed. Console commands used to conﬁgure the unit will report that the unit is in DIP switch conﬁguration and will not change the conﬁguration. Likewise, EOC variables cannot be used to conﬁgure the device. Also note that changing the DIP switch settings while the unit is running will have no effect on the conﬁgura- tion as the DIP switches are only read on startup.

Software conﬁguration mode is entered by starting the unit with the DIP switches set to all ON. The system then reads any conﬁguration that might have been saved to FLASH. If no conﬁguration has been saved, then the factory defaults are loaded. The unit may be further conﬁgured by console commands or by EOC.

8

Image 8

Contents User Manual Contents Operation Remote Console Manual InformationCompliance Information Radio and TV Interference FCC Part 68 Acta StatementIndustry Canada Notice CE NoticeTel +1 301 Email support@patton.com Warranty InformationService Description FeaturesGeneral Information Configuration Model 3088 3088/D version shownParameter Description Possible Default Values OFF, LAL Parameter Description Possible Default Configuring the DIP SwitchesSystem Reset Mode Software UpgradesPosition Function Factory Default Conﬁguration Reset to Factory DefaultsDIP Switch Settings S1-7 S1-6 S1-5 S1-4 S1-3 S1-2 S1-1 Data Rate Kbps S1-8 TX Clock Setting DescriptionS1-7 S1-1 Data Rate 1920 S2-6 Setting S2-5 S2-4 Clock ModeS2-5 S2-4 Clock Mode Description LoopsS2-1 Front Panel Switches S2-3 Annex A/BS2-3 Annex S2-2 Line ProbePage DSL Line Condition Good or Poor CRCHelp Commands System Conﬁguration CommandsSystem show clockmode Shows the clock mode System Status CommandsDSL Conﬁguration Commands Startup Delay Interval Interval totintDSL Status Commands Page Example Command Line Interface Session Remote ConsoleRocketlink Plug ‘N’ Play 3096RC Installation Connecting the Twisted Pair InterfaceConnecting the Model 3088/CA Serial Interface Connecting the Model 3088/CA V.35 to a DTE DeviceConnecting the Model 3088/D X.21 to a DCE or DTE Device Connecting the Model 3088/CA V.35 to a DCE DeviceConnecting the Model 3088/D X.21 Serial Interface Connecting the Model 3088/D to X.21 DTE or DCE Opening the CaseConnecting Power POWER-UP Power GreenOperation LED Status MonitorsTerm Green 3088/D with the X.21 interfaceTM/ER Red Test ModesLocal Analog Loopback diagram PatternsEstablishing a Remote Console Session How to ConnectRemote Console Manual Information Page System show status command shows that DSL link is not up How to DisconnectDifferences in Local and Remote Control Session Behavior LAL Model 3088 Software Upgrade Feature Reset Configuration to Factory Defaults Serial Connector DiagnosticsAppendix a Clocking ModesPower ComplianceTransmission Line Line CodingEnvironment Line Interface14 G.SHDSL Physical Connection Appendix B Model # DescriptionPin # Signal Appendix CPin Signal Appendix D