Patton electronic 3088 user manual DSL Status Commands

Page 23

•dsl set errmon startdelay <startdelay>: Sets the number of seconds to wait after the DSL link comes up before the error monitor starts inspecting intervals.

The following commands display the current DSL conﬁguration:

•dsl show annex: Shows the currently selected G.SH Annex.

•dsl show lineprobe: Shows whether or not Line Probe is currently enabled.

•dsl show loopback: Shows which loopback is currently running.

•dsl show pattern: Shows what PRBS pattern is currently running.

The following commands display the current DSL error monitor conﬁguration:

•dsl show errmon maxint: Shows the maximum errors allowed in an interval before it is considered errored.

•dsl show errmon inttime: Shows the length in seconds of each interval.

•dsl show errmon intcnt: Shows the number of errored intervals allowed before restarting.

•dsl show errmon totint: Shows the number of intervals to monitor before disabling the error monitor.

•dsl show errmon startdelay: Shows the length in seconds to wait after the DSL link comes up before starting the error monitor.

Changing the data rate (system set timeslots), the clock mode (system set clockmode), the Annex (dsl set annex), or Line Probe (dsl set lineprobe), or the DSL error monitor settings will not take effect on the DSL link until the link restarts. The dsl start command restarts the DSL link.

DSL Status Commands

The following commands display DSL status:

•dsl show status: Shows the following DSL status information: link state, sync state, link speed, error counters, line condition, and noise margin.

•dsl show linkstate: Shows the state of the DSL link: idle, success, deactivated, or in progress.

23

Image 23

Contents User Manual Contents Remote Console Manual Information OperationFCC Part 68 Acta Statement Compliance Information Radio and TV InterferenceCE Notice Industry Canada NoticeTel +1 301 Email support@patton.com Warranty InformationService Description FeaturesGeneral Information Model 3088 3088/D version shown ConfigurationParameter Description Possible Default Values OFF, LAL Configuring the DIP Switches Parameter Description Possible DefaultSoftware Upgrades System Reset ModePosition Function Factory Default Conﬁguration Reset to Factory DefaultsDIP Switch Settings S1-7 S1-6 S1-5 S1-4 S1-3 S1-2 S1-1 Data Rate Kbps S1-8 TX Clock Setting DescriptionS1-7 S1-1 Data Rate 1920 Loops S2-6 SettingS2-5 S2-4 Clock Mode S2-5 S2-4 Clock Mode DescriptionS2-2 Line Probe S2-1 Front Panel SwitchesS2-3 Annex A/B S2-3 AnnexPage CRC DSL Line Condition Good or PoorSystem Conﬁguration Commands Help CommandsSystem Status Commands System show clockmode Shows the clock modeStartup Delay Interval Interval totint DSL Conﬁguration CommandsDSL Status Commands Page Remote Console Example Command Line Interface SessionRocketlink Plug ‘N’ Play 3096RC Connecting the Twisted Pair Interface InstallationConnecting the Model 3088/CA V.35 to a DTE Device Connecting the Model 3088/CA Serial InterfaceConnecting the Model 3088/D X.21 to a DCE or DTE Device Connecting the Model 3088/CA V.35 to a DCE DeviceConnecting the Model 3088/D X.21 Serial Interface Opening the Case Connecting the Model 3088/D to X.21 DTE or DCEConnecting Power LED Status Monitors POWER-UPPower Green OperationTest Modes Term Green3088/D with the X.21 interface TM/ER RedPatterns Local Analog Loopback diagramEstablishing a Remote Console Session How to ConnectRemote Console Manual Information Page How to Disconnect System show status command shows that DSL link is not upDifferences in Local and Remote Control Session Behavior LAL Model 3088 Software Upgrade Feature Reset Configuration to Factory Defaults Clocking Modes Serial ConnectorDiagnostics Appendix aLine Coding PowerCompliance Transmission LineEnvironment Line Interface14 G.SHDSL Physical Connection Model # Description Appendix BAppendix C Pin # SignalAppendix D Pin Signal