Patton electronic 3088 user manual Rocketlink Plug ‘N’ Play

Page 26

password: ******

>dsl clear errcntrs

>dsl show errcntrs

crc:0

losw: 0

tx fifo full: 0

tx fifo empty: 0

tx fifo slip: 0

tx stuff: 0

rx fifo full: 0

rx fifo empty: 0

rx fifo slip: 0

>logout

exiting remote console

>dsl set loopback rdl

>dsl set pattern 511e

>dsl show testmode ber status: in progress

errors: 42

time: 12

>dsl set pattern off

>dsl set loopback off

>logout

password:

4.4 ROCKETLINK PLUG ‘N’ PLAY

The RocketLink Plug ‘n’ Play feature allows ISPs, carriers and PTTs to quickly upgrade the link speed for a customer without requiring a visit to re-conﬁgure the Customer Premise (CP) Model 3088. This feature also allows service providers to set up all of the conﬁgurations at the Central Ofﬁce (via the ForeFront AIS system) before installing the stand alone units, saving time spent conﬁguring or re-conﬁguring DIP switches.

Note RocketLink Plug ‘n’ Play is only available when using a Fore- Front Model 3096RC as the CO unit.

The RocketLink Plug ‘n’ Play feature allows the user to conﬁgure the DTE rate (bandwidth allocation, see Switches S1-1 through S1-7) of the CP unit via the ForeFront Model 3096RC at the Central Ofﬁce (CO). The stand alone unit at the Customer Premise (CP) site will automatically conﬁgure itself to the DTE rate (Bandwidth Allocation) deﬁned at the Model 3096RC. Other conﬁguration parameters remain in the

default setting.

26

Image 26

Contents User Manual Contents Operation Remote Console Manual InformationCompliance Information Radio and TV Interference FCC Part 68 Acta StatementIndustry Canada Notice CE NoticeTel +1 301 Email support@patton.com Warranty InformationService Description FeaturesGeneral Information Configuration Model 3088 3088/D version shownParameter Description Possible Default Values OFF, LAL Parameter Description Possible Default Configuring the DIP SwitchesSystem Reset Mode Software UpgradesPosition Function Factory Default Conﬁguration Reset to Factory DefaultsDIP Switch Settings S1-7 S1-6 S1-5 S1-4 S1-3 S1-2 S1-1 Data Rate Kbps S1-8 TX Clock Setting DescriptionS1-7 S1-1 Data Rate 1920 S2-5 S2-4 Clock Mode Description S2-6 SettingS2-5 S2-4 Clock Mode LoopsS2-3 Annex S2-1 Front Panel SwitchesS2-3 Annex A/B S2-2 Line ProbePage DSL Line Condition Good or Poor CRCHelp Commands System Conﬁguration CommandsSystem show clockmode Shows the clock mode System Status CommandsDSL Conﬁguration Commands Startup Delay Interval Interval totintDSL Status Commands Page Example Command Line Interface Session Remote ConsoleRocketlink Plug ‘N’ Play 3096RC Installation Connecting the Twisted Pair InterfaceConnecting the Model 3088/CA Serial Interface Connecting the Model 3088/CA V.35 to a DTE DeviceConnecting the Model 3088/D X.21 to a DCE or DTE Device Connecting the Model 3088/CA V.35 to a DCE DeviceConnecting the Model 3088/D X.21 Serial Interface Connecting the Model 3088/D to X.21 DTE or DCE Opening the CaseConnecting Power Operation POWER-UPPower Green LED Status MonitorsTM/ER Red Term Green3088/D with the X.21 interface Test ModesLocal Analog Loopback diagram PatternsEstablishing a Remote Console Session How to ConnectRemote Console Manual Information Page System show status command shows that DSL link is not up How to DisconnectDifferences in Local and Remote Control Session Behavior LAL Model 3088 Software Upgrade Feature Reset Configuration to Factory Defaults Appendix a Serial ConnectorDiagnostics Clocking ModesTransmission Line PowerCompliance Line CodingEnvironment Line Interface14 G.SHDSL Physical Connection Appendix B Model # DescriptionPin # Signal Appendix CPin Signal Appendix D