Patton electronic 4830 manual Analog VoIP Integrated Access Device

Page 1

SmartNode 4830 Series

Analog VoIP Integrated Access Device

Getting Started Guide

Approval

Models that are equipped with telecom interfaces have been approved for connection to the public telecommunication network as listed under PSTN regulatory compliance.

Important

This is a Class A device and is intended for use in a light industrial environment. It is not intended nor approved for use in an industrial or residential environment.

Sales Ofﬁce: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail:support@patton.com

WWW: www.patton.com

Document Number: 13219U1-001 Rev. C

Part Number: 07MSN4830-GS

Revised: May 16, 2007

Image 1

Contents

Analog VoIP Integrated Access Device Mailsupport@patton.com Summary Table of Contents Table of Contents LEDs status and monitoring Specifications SmartNode 4830 Series factory configuration List of Figures List of Tables Audience About this guideStructure Impaired functioning PrecautionsSafety when working with electricity General observations Typographical conventions used in this documentGeneral conventions SmartNode 4830 Getting Started GuideAbout this guide General information Chapter contentsSmartNode product SmartNode 4838 shown SmartNode Model 4830 Series OverviewGeneral information Examples of SN4830 Series rear panels FXS only SmartNode 4830 Series Detailed DescriptionModel SN4832/JOX*/EUI FXO ports DSL connector SmartNode 4830 Series power input connector Ports descriptions SmartNode 4830 Series front panels FXS only Console Applications overview Introduction Multiservice carrier access over leased linesApplications for SmartNode 4830 Series Converged enterprise network over leased line Converged enterprise network over leased lineHardware installation Create a network diagram see section Network information on Planning the installationInstallation checklist Network information Site logIP related information Installing the VoIP IAD Analog FXS connection RJ-11 pinout diagram RJ-11 socket Installing the Ethernet cable Installing the serial WAN cable DCD Hardware installation Rear panel of SN4830 T1/E1 -/K Model Pins not listed are not used Connecting to external power source Power VoIP Link Getting started with the SmartNode Steps for setting up a new SmartNode Conﬁgure IP address Power connection and default conﬁgurationConnect with the serial interface Changing the IP address LoginLoad conﬁguration Connect the SmartNode to the networkStart Bootloader BootloaderLoad a new application image SmartWare via Tftp Start-up with factory conﬁgurationCopy tftp//tftpserveraddress/server path/b1 flash Load a new application image SmartWare via the serial link Additional informationLEDs status and monitoring Status LEDs LEDs status and monitoring SmartNode LED Indications Contacting Patton for assistance Contact information Warranty coveragePatton support headquarters in the USA RMA numbers Out-of-warranty serviceAppendix a Compliance information Compliance Safety complianceRadio and TV Interference FCC Part EMC complianceIndustry Canada Notice FXO ports FCC Part 68 Acta Statement FXO portsAuthorized European Representative CE NoticeAppendix B Speciﬁcations Ethernet interface Voice connectivitySync serial interface if applicable T1/E1 interface if applicableShdsl Daughter Card if applicable Adsl Daughter Card if applicableVoice signaling Voice processing signaling dependentPPP and Frame-Relay support Fax and modem supportVoice routing-session product IP servicesManagement Weight and power dissipation DimensionsPower supply Operating environmentSmartNode Model SysObjectID Identiﬁcation of the SmartNode devices via SnmpAppendix C Cabling Serial console Connecting a serial terminalEthernet straight-through Ethernet 10Base-T and 100Base-TAnalog FXS Connecting an FXS deviceAnalog FXO Connecting to an FXO line socketDSL T1/E1Appendix D Port pin-outs Ethernet 10Base-T and 100Base-T port Console portSerial port Sync Serial PortFXO port FXS portADSL/G.SHDSL port T1/E1 portAppendix E SmartNode 4830 Series factory conﬁguration SmartNode 4830 Series factory configuration Appendix F Installation checklist Task Veriﬁed by Date Appendix G Accessories Description Part Number