Patton electronic 4830 manual Copy tftp//tftpserveraddress/server path/b1 flash

Page 50

SmartNode 4830 Getting Started Guide4 • Getting started with the SmartNode

Step	Command	Purpose

8	RedBoot> go	Starts the application image that was down-
		loaded into the volatile memory (RAM).

Note With the Bootloader, only the Ethernet interface 0/0 is available. The Boot- loader applies the IP address, subnet mask, and default gateway that were last conﬁgured by the Bootloader itself or by another application (e.g. Smart- Ware). If an application conﬁgured the Ethernet interface 0/0 to use DHCP, the Bootloader will also use DHCP to learn the interface conﬁguration. It can receive and apply the IP address, subnet mask, default gateway, and default (TFTP) server (transmitted as basic DHCP information ‘Next server IP address’).

Note This procedure does not download the respective CLI description ﬁle.

Download it after starting up SmartWare with the following command:

copy tftp://<tftp_server_address>/<server path>/b1 flash:

Example: Downloading and storing a new application image (SmartWare)

RedBoot> ip -l 172.16.40.98/19 RedBoot> ip -g 172.16.32.1 RedBoot> ping -h 172.16.32.100

Network PING - from 172.16.40.98 to 172.16.32.100

..........PING - received 10 of 10 expected

RedBoot> load -r -v -h 172.16.32.100 -b 0x1800100 /Sn4xxx/image.bin Using default protocol (TFTP)

-

Raw file loaded 0x01800100-0x0199ca6b, 1689964 bytes, assumed entry at 0x01800100

RedBoot> fis delete -n 1

Delete image 1 - continue (y/n)? y

... Erase from 0x60030000-0x601cc974: ..........................

RedBoot> fis create

Use address 0x01800100, size 1684402 ? - continue (y/n)? y

... Erase from 0x60030000-0x601cb3ba:			..........................
... Program from 0x00011eec-0x00011ef4 at 0x60030000: .
... Program from 0x01800100-0x0199b4b2 at 0x60030008:
... Program from 0x00011eec-0x00011ef4 at 0x60030000: .
Image successfully written to flash
RedBoot> fis list -l
Id Address	Length	State	Description
Entry	Load Addr		Version

--------------------------------------------------------------------

1 0x60030000		1693438	valid	SmartWare R2.10 BUILD28015
0x01800100		0x01800100		V2.10
RedBoot>	go
Starting	'SmartWare R2.10		BUILD28015' at 0x01800100 via 0x01800100

Bootloader

50

Image 50

Contents

Analog VoIP Integrated Access Device Mailsupport@patton.com Summary Table of Contents Table of Contents LEDs status and monitoring Specifications SmartNode 4830 Series factory configuration List of Figures List of Tables Structure About this guideAudience Precautions Impaired functioningSafety when working with electricity General conventions Typographical conventions used in this documentGeneral observations SmartNode 4830 Getting Started GuideAbout this guide Chapter contents General informationSmartNode Model 4830 Series Overview SmartNode product SmartNode 4838 shownGeneral information SmartNode 4830 Series Detailed Description Examples of SN4830 Series rear panels FXS onlyModel SN4832/JOX*/EUI FXO ports DSL connector SmartNode 4830 Series power input connector Ports descriptions SmartNode 4830 Series front panels FXS only Console Applications overview Applications for SmartNode 4830 Series Multiservice carrier access over leased linesIntroduction Converged enterprise network over leased line Converged enterprise network over leased lineHardware installation Planning the installation Create a network diagram see section Network information onInstallation checklist IP related information Site logNetwork information Installing the VoIP IAD Analog FXS connection RJ-11 pinout diagram RJ-11 socket Installing the Ethernet cable Installing the serial WAN cable DCD Hardware installation Rear panel of SN4830 T1/E1 -/K Model Pins not listed are not used Connecting to external power source Power VoIP Link Getting started with the SmartNode Steps for setting up a new SmartNode Connect with the serial interface Power connection and default conﬁgurationConﬁgure IP address Login Changing the IP addressConnect the SmartNode to the network Load conﬁgurationBootloader Start BootloaderStart-up with factory conﬁguration Load a new application image SmartWare via TftpCopy tftp//tftpserveraddress/server path/b1 flash Additional information Load a new application image SmartWare via the serial linkLEDs status and monitoring Status LEDs LEDs status and monitoring SmartNode LED Indications Contacting Patton for assistance Patton support headquarters in the USA Warranty coverageContact information Out-of-warranty service RMA numbersAppendix a Compliance information Radio and TV Interference FCC Part Safety complianceCompliance EMC complianceFCC Part 68 Acta Statement FXO ports Industry Canada Notice FXO portsCE Notice Authorized European RepresentativeAppendix B Speciﬁcations Sync serial interface if applicable Voice connectivityEthernet interface T1/E1 interface if applicableAdsl Daughter Card if applicable Shdsl Daughter Card if applicablePPP and Frame-Relay support Voice processing signaling dependentVoice signaling Fax and modem supportManagement IP servicesVoice routing-session product Power supply DimensionsWeight and power dissipation Operating environmentIdentiﬁcation of the SmartNode devices via Snmp SmartNode Model SysObjectIDAppendix C Cabling Connecting a serial terminal Serial consoleEthernet 10Base-T and 100Base-T Ethernet straight-throughConnecting an FXS device Analog FXSConnecting to an FXO line socket Analog FXOT1/E1 DSLAppendix D Port pin-outs Console port Ethernet 10Base-T and 100Base-T portSync Serial Port Serial portFXS port FXO portT1/E1 port ADSL/G.SHDSL portAppendix E SmartNode 4830 Series factory conﬁguration SmartNode 4830 Series factory configuration Appendix F Installation checklist Task Veriﬁed by Date Appendix G Accessories Description Part Number