Patton electronic 4830 manual Dcd

Page 37

SmartNode 4830 Getting Started Guide	3 • Hardware installation

Installing the DSL interface cable. The SmartNode Model 4830 comes with an option for a G.SHDSL or ADSL interface. Use a straight-through RJ-11 cable to connect the DSL port.

Installing the V.35 interface cable. The SmartNode Model 4830 comes with a V.35 interface presented on a DB-25 female connector (see ﬁgure 16).

V.35 serial port connector

Figure 16. Rear view of the SN4830 showing location of V.35 interface connector

The signal pin-outs for the Model 4830 V.35 interface are shown in table 7.

Table 7. Signal pin-outs for the V.35 interface on the SmartNode 4830

Pin	Signal	Pin	Signal

1	Frame Ground	12	TXCb

2	TXDa	14	TXDb

3	RXDa	15	RXCa

4	RTS	16	RXDb

5	CTS	17	RXCa

6	DSR	18	LL

7	Signal Ground	20	DTR

8	DCD	21	RL

9	RXCb	24	EXTCa

11	EXTCb

The SN4830’s V.35 interface is wired as a DTE. No DCE conﬁguration is possible. If you are directly connect- ing the SN4830’s V.35 interface to third-party equipment that cannot be conﬁgured as a DCE, you must use a

Installing the VoIP IAD

37

Image 37

Contents

Analog VoIP Integrated Access Device Mailsupport@patton.com Summary Table of Contents Table of Contents LEDs status and monitoring Specifications SmartNode 4830 Series factory configuration List of Figures List of Tables Audience About this guideStructure Impaired functioning PrecautionsSafety when working with electricity General observations Typographical conventions used in this documentGeneral conventions SmartNode 4830 Getting Started GuideAbout this guide General information Chapter contentsSmartNode product SmartNode 4838 shown SmartNode Model 4830 Series OverviewGeneral information Examples of SN4830 Series rear panels FXS only SmartNode 4830 Series Detailed DescriptionModel SN4832/JOX*/EUI FXO ports DSL connector SmartNode 4830 Series power input connector Ports descriptions SmartNode 4830 Series front panels FXS only Console Applications overview Introduction Multiservice carrier access over leased linesApplications for SmartNode 4830 Series Converged enterprise network over leased line Converged enterprise network over leased lineHardware installation Create a network diagram see section Network information on Planning the installationInstallation checklist Network information Site logIP related information Installing the VoIP IAD Analog FXS connection RJ-11 pinout diagram RJ-11 socket Installing the Ethernet cable Installing the serial WAN cable DCD Hardware installation Rear panel of SN4830 T1/E1 -/K Model Pins not listed are not used Connecting to external power source Power VoIP Link Getting started with the SmartNode Steps for setting up a new SmartNode Conﬁgure IP address Power connection and default conﬁgurationConnect with the serial interface Changing the IP address LoginLoad conﬁguration Connect the SmartNode to the networkStart Bootloader BootloaderLoad a new application image SmartWare via Tftp Start-up with factory conﬁgurationCopy tftp//tftpserveraddress/server path/b1 flash Load a new application image SmartWare via the serial link Additional informationLEDs status and monitoring Status LEDs LEDs status and monitoring SmartNode LED Indications Contacting Patton for assistance Contact information Warranty coveragePatton support headquarters in the USA RMA numbers Out-of-warranty serviceAppendix a Compliance information Compliance Safety complianceRadio and TV Interference FCC Part EMC complianceIndustry Canada Notice FXO ports FCC Part 68 Acta Statement FXO portsAuthorized European Representative CE NoticeAppendix B Speciﬁcations Ethernet interface Voice connectivitySync serial interface if applicable T1/E1 interface if applicableShdsl Daughter Card if applicable Adsl Daughter Card if applicableVoice signaling Voice processing signaling dependentPPP and Frame-Relay support Fax and modem supportVoice routing-session product IP servicesManagement Weight and power dissipation DimensionsPower supply Operating environmentSmartNode Model SysObjectID Identiﬁcation of the SmartNode devices via SnmpAppendix C Cabling Serial console Connecting a serial terminalEthernet straight-through Ethernet 10Base-T and 100Base-TAnalog FXS Connecting an FXS deviceAnalog FXO Connecting to an FXO line socketDSL T1/E1Appendix D Port pin-outs Ethernet 10Base-T and 100Base-T port Console portSerial port Sync Serial PortFXO port FXS portADSL/G.SHDSL port T1/E1 portAppendix E SmartNode 4830 Series factory conﬁguration SmartNode 4830 Series factory configuration Appendix F Installation checklist Task Veriﬁed by Date Appendix G Accessories Description Part Number