Patton electronic 4830 manual Planning the installation

Page 29

SmartNode 4830 Getting Started Guide	3 • Hardware installation

Planning the installation

Before you start the actual installation, we strongly recommend that you gather all the information you will need to install and setup the device. See table 3 for an example of what pre-installment checks you might need to carry out. Completing the pre-installation checks enables you to install and set up your VoIP IAD within an existing network infrastructure with conﬁdence.

WARNING

Note

Mains Voltage: Do not open the case when the power cord is connected. For systems without a power switch, line voltages are present within the power supply when the power cord is connected. The mains outlet that is utilized to power the SmartNode router shall be within 10 feet (3 meters) of the device, shall be easily accessible, and protected by a circuit breaker.

When setting up your VoIP IAD you must consider cable-length lim- itations, and potential electromagnetic interference (EMI) as deﬁned by the applicable local and international regulations. Ensure that your site is properly prepared before beginning installation.

Before installing the VoIP IAD device, the following tasks should be completed:

•Create a network diagram (see section “Network information” on page 31)

•Gather IP related information (see section “IP related information” on page 31 for more information)

•Install the hardware and software needed to conﬁgure the SmartNode. (See section “Software tools” on page 32)

•Verify power source reliability (see section “Power source” on page 32).

When you ﬁnish preparing for your VoIP IAD installation, go to section “Installing the VoIP IAD” on page 32 to install the device.

Planning the installation

29

Image 29

Contents

Analog VoIP Integrated Access Device Mailsupport@patton.com Summary Table of Contents Table of Contents LEDs status and monitoring Specifications SmartNode 4830 Series factory configuration List of Figures List of Tables Structure About this guideAudience Impaired functioning PrecautionsSafety when working with electricity General conventions Typographical conventions used in this documentGeneral observations SmartNode 4830 Getting Started GuideAbout this guide General information Chapter contentsSmartNode product SmartNode 4838 shown SmartNode Model 4830 Series OverviewGeneral information Examples of SN4830 Series rear panels FXS only SmartNode 4830 Series Detailed DescriptionModel SN4832/JOX*/EUI FXO ports DSL connector SmartNode 4830 Series power input connector Ports descriptions SmartNode 4830 Series front panels FXS only Console Applications overview Applications for SmartNode 4830 Series Multiservice carrier access over leased linesIntroduction Converged enterprise network over leased line Converged enterprise network over leased lineHardware installation Create a network diagram see section Network information on Planning the installationInstallation checklist IP related information Site logNetwork information Installing the VoIP IAD Analog FXS connection RJ-11 pinout diagram RJ-11 socket Installing the Ethernet cable Installing the serial WAN cable DCD Hardware installation Rear panel of SN4830 T1/E1 -/K Model Pins not listed are not used Connecting to external power source Power VoIP Link Getting started with the SmartNode Steps for setting up a new SmartNode Connect with the serial interface Power connection and default conﬁgurationConﬁgure IP address Changing the IP address LoginLoad conﬁguration Connect the SmartNode to the networkStart Bootloader BootloaderLoad a new application image SmartWare via Tftp Start-up with factory conﬁgurationCopy tftp//tftpserveraddress/server path/b1 flash Load a new application image SmartWare via the serial link Additional informationLEDs status and monitoring Status LEDs LEDs status and monitoring SmartNode LED Indications Contacting Patton for assistance Patton support headquarters in the USA Warranty coverageContact information RMA numbers Out-of-warranty serviceAppendix a Compliance information Compliance Safety complianceRadio and TV Interference FCC Part EMC complianceIndustry Canada Notice FXO ports FCC Part 68 Acta Statement FXO portsAuthorized European Representative CE NoticeAppendix B Speciﬁcations Ethernet interface Voice connectivitySync serial interface if applicable T1/E1 interface if applicableShdsl Daughter Card if applicable Adsl Daughter Card if applicableVoice signaling Voice processing signaling dependentPPP and Frame-Relay support Fax and modem supportManagement IP servicesVoice routing-session product Weight and power dissipation DimensionsPower supply Operating environmentSmartNode Model SysObjectID Identiﬁcation of the SmartNode devices via SnmpAppendix C Cabling Serial console Connecting a serial terminalEthernet straight-through Ethernet 10Base-T and 100Base-TAnalog FXS Connecting an FXS deviceAnalog FXO Connecting to an FXO line socketDSL T1/E1Appendix D Port pin-outs Ethernet 10Base-T and 100Base-T port Console portSerial port Sync Serial PortFXO port FXS portADSL/G.SHDSL port T1/E1 portAppendix E SmartNode 4830 Series factory conﬁguration SmartNode 4830 Series factory configuration Appendix F Installation checklist Task Veriﬁed by Date Appendix G Accessories Description Part Number