Patton electronic 4830 manual Description Part Number

Page 86

SmartNode 4900 Getting Started Guide	G • Accessories

Introduction

The cables listed in table 23 are available as accessories for the SmartNode 4900 Series products.

Table 23. Accessory cables

Description	Part Number

DB-25 male to M/34 male cable (Sync serial v.35 port)	1205-25M/35M

DB-25 male to M/34 female cable (Sync serial v.35 port)	1205-25M/35M

DB-15 male to DB-15 male cable (Sync serial x.21 port)	EMEM216006

Introduction

86

Image 86

Contents

Analog VoIP Integrated Access Device Mailsupport@patton.com Summary Table of Contents Table of Contents LEDs status and monitoring Specifications SmartNode 4830 Series factory configuration List of Figures List of Tables Structure About this guideAudience Precautions Impaired functioningSafety when working with electricity General conventions Typographical conventions used in this documentGeneral observations SmartNode 4830 Getting Started GuideAbout this guide Chapter contents General informationSmartNode Model 4830 Series Overview SmartNode product SmartNode 4838 shownGeneral information SmartNode 4830 Series Detailed Description Examples of SN4830 Series rear panels FXS onlyModel SN4832/JOX*/EUI FXO ports DSL connector SmartNode 4830 Series power input connector Ports descriptions SmartNode 4830 Series front panels FXS only Console Applications overview Applications for SmartNode 4830 Series Multiservice carrier access over leased linesIntroduction Converged enterprise network over leased line Converged enterprise network over leased lineHardware installation Planning the installation Create a network diagram see section Network information onInstallation checklist IP related information Site logNetwork information Installing the VoIP IAD Analog FXS connection RJ-11 pinout diagram RJ-11 socket Installing the Ethernet cable Installing the serial WAN cable DCD Hardware installation Rear panel of SN4830 T1/E1 -/K Model Pins not listed are not used Connecting to external power source Power VoIP Link Getting started with the SmartNode Steps for setting up a new SmartNode Connect with the serial interface Power connection and default conﬁgurationConﬁgure IP address Login Changing the IP addressConnect the SmartNode to the network Load conﬁgurationBootloader Start BootloaderStart-up with factory conﬁguration Load a new application image SmartWare via TftpCopy tftp//tftpserveraddress/server path/b1 flash Additional information Load a new application image SmartWare via the serial linkLEDs status and monitoring Status LEDs LEDs status and monitoring SmartNode LED Indications Contacting Patton for assistance Patton support headquarters in the USA Warranty coverageContact information Out-of-warranty service RMA numbersAppendix a Compliance information Radio and TV Interference FCC Part Safety complianceCompliance EMC complianceFCC Part 68 Acta Statement FXO ports Industry Canada Notice FXO portsCE Notice Authorized European RepresentativeAppendix B Speciﬁcations Sync serial interface if applicable Voice connectivityEthernet interface T1/E1 interface if applicableAdsl Daughter Card if applicable Shdsl Daughter Card if applicablePPP and Frame-Relay support Voice processing signaling dependentVoice signaling Fax and modem supportManagement IP servicesVoice routing-session product Power supply DimensionsWeight and power dissipation Operating environmentIdentiﬁcation of the SmartNode devices via Snmp SmartNode Model SysObjectIDAppendix C Cabling Connecting a serial terminal Serial consoleEthernet 10Base-T and 100Base-T Ethernet straight-throughConnecting an FXS device Analog FXSConnecting to an FXO line socket Analog FXOT1/E1 DSLAppendix D Port pin-outs Console port Ethernet 10Base-T and 100Base-T portSync Serial Port Serial portFXS port FXO portT1/E1 port ADSL/G.SHDSL portAppendix E SmartNode 4830 Series factory conﬁguration SmartNode 4830 Series factory configuration Appendix F Installation checklist Task Veriﬁed by Date Appendix G Accessories Description Part Number