Patton electronic 4830 manual PPP and Frame-Relay support, Voice processing signaling dependent

Page 66

SmartNode 4830 Getting Started Guide	B • Specifications

PPP and Frame-Relay support

X.21 or V.35 WAN

Frame-Relay (8 PVCs)

RFC1490, FRF.12 fragmentation

LMI, Q.933D, ANSI 617D, Gang of Four

PPP, PAP, CHAP, LCP, IPCP

Voice processing (signaling dependent)

Voice codes:

•G.711 A-Law/µ-Law (64 kbps)

•G.726 (ADPCM 40, 32, 24, 16 kbps)

•G.723.1 (5.3 or 6.3 kbps)

•G.729ab (8 kbps)

•Transparent pass through

G.168 echo cancellation

8 parallel voice connections DTMF detection and generation Carrier tone detection and generation Silence suppression and comfort noise Conﬁgurable dejitter buffer Conﬁgurable tones (dial, ringing, busy) Conﬁgurable transmit packet length RTP/RTCP (RFC 1889)

Fax and modem support

G.711 transparent FAX

Fax over IP (FoIP)

T.38 Fax relay (9.6 k, 14.4 k)

Voice signaling

H.323v4

•RAS, H.225, H.245

•Fast-connect, early H.245

•Gatekeeper autodiscovery

PPP and Frame-Relay support

66

Image 66

Contents

Analog VoIP Integrated Access Device Mailsupport@patton.com Summary Table of Contents Table of Contents LEDs status and monitoring Specifications SmartNode 4830 Series factory configuration List of Figures List of Tables About this guide AudienceStructure Precautions Impaired functioningSafety when working with electricity Typographical conventions used in this document General observationsGeneral conventions SmartNode 4830 Getting Started GuideAbout this guide Chapter contents General informationSmartNode Model 4830 Series Overview SmartNode product SmartNode 4838 shownGeneral information SmartNode 4830 Series Detailed Description Examples of SN4830 Series rear panels FXS onlyModel SN4832/JOX*/EUI FXO ports DSL connector SmartNode 4830 Series power input connector Ports descriptions SmartNode 4830 Series front panels FXS only Console Applications overview Multiservice carrier access over leased lines IntroductionApplications for SmartNode 4830 Series Converged enterprise network over leased line Converged enterprise network over leased lineHardware installation Planning the installation Create a network diagram see section Network information onInstallation checklist Site log Network informationIP related information Installing the VoIP IAD Analog FXS connection RJ-11 pinout diagram RJ-11 socket Installing the Ethernet cable Installing the serial WAN cable DCD Hardware installation Rear panel of SN4830 T1/E1 -/K Model Pins not listed are not used Connecting to external power source Power VoIP Link Getting started with the SmartNode Steps for setting up a new SmartNode Power connection and default conﬁguration Conﬁgure IP addressConnect with the serial interface Login Changing the IP addressConnect the SmartNode to the network Load conﬁgurationBootloader Start BootloaderStart-up with factory conﬁguration Load a new application image SmartWare via TftpCopy tftp//tftpserveraddress/server path/b1 flash Additional information Load a new application image SmartWare via the serial linkLEDs status and monitoring Status LEDs LEDs status and monitoring SmartNode LED Indications Contacting Patton for assistance Warranty coverage Contact informationPatton support headquarters in the USA Out-of-warranty service RMA numbersAppendix a Compliance information Radio and TV Interference FCC Part Safety complianceCompliance EMC complianceFCC Part 68 Acta Statement FXO ports Industry Canada Notice FXO ports CE Notice Authorized European RepresentativeAppendix B Speciﬁcations Sync serial interface if applicable Voice connectivityEthernet interface T1/E1 interface if applicableAdsl Daughter Card if applicable Shdsl Daughter Card if applicablePPP and Frame-Relay support Voice processing signaling dependentVoice signaling Fax and modem supportIP services Voice routing-session productManagement Power supply DimensionsWeight and power dissipation Operating environmentIdentiﬁcation of the SmartNode devices via Snmp SmartNode Model SysObjectIDAppendix C Cabling Connecting a serial terminal Serial consoleEthernet 10Base-T and 100Base-T Ethernet straight-throughConnecting an FXS device Analog FXSConnecting to an FXO line socket Analog FXOT1/E1 DSLAppendix D Port pin-outs Console port Ethernet 10Base-T and 100Base-T portSync Serial Port Serial portFXS port FXO portT1/E1 port ADSL/G.SHDSL portAppendix E SmartNode 4830 Series factory conﬁguration SmartNode 4830 Series factory configuration Appendix F Installation checklist Task Veriﬁed by Date Appendix G Accessories Description Part Number